{"product_id":"is200erioh1abc-general-electric-i-o-regulator-module-new-original-stock","title":"IS200ERIOH1ABC General Electric I\/O Regulator Module | New \u0026 Original Stock","description":"\u003cp\u003eThe \u003cstrong\u003eGeneral Electric IS200ERIOH1ABC\u003c\/strong\u003e, also cataloged as the \u003cstrong\u003eIS200ERIOH1ABC\u003c\/strong\u003e I\/O Regulator Module, operates as a dedicated hardware component for control and regulation within EX2100 Excitation Control and Mark VI system platforms.\u003c\/p\u003e\n\u003ch3\u003eHardware Specifications\u003c\/h3\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003e\u003cstrong\u003eParameter\u003c\/strong\u003e\u003c\/th\u003e\n\u003cth\u003e\u003cstrong\u003eSpecification\u003c\/strong\u003e\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eModel\u003c\/td\u003e\n\u003ctd\u003eIS200ERIOH1ABC\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBrand\u003c\/td\u003e\n\u003ctd\u003eGeneral Electric\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOrigin\u003c\/td\u003e\n\u003ctd\u003eUnited States\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWeight\u003c\/td\u003e\n\u003ctd\u003e0.5 kg\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDimensions\u003c\/td\u003e\n\u003ctd\u003e18.7 x 12.5 x 3.5 cm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOperating Temp\u003c\/td\u003e\n\u003ctd\u003e0 to 60 deg C\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePower Consumption\u003c\/td\u003e\n\u003ctd\u003e24 VDC\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eI\/O Channels\u003c\/td\u003e\n\u003ctd\u003e16\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eIsolation\u003c\/td\u003e\n\u003ctd\u003e1500 V RMS\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003ch3\u003eProfinet \/ EtherNet\/IP Deterministic Networks\u003c\/h3\u003e\n\u003cp\u003eThe IS200ERIOH1ABC utilizes dual 100 MB Ethernet ports to maintain deterministic communication across the control network. It provides high-speed processing for 16 input\/output channels, featuring a response time of less than 1 ms to ensure real-time regulation of excitation parameters. The module architecture incorporates 1500 V RMS galvanic isolation between the field side and the logic side to protect internal processing circuits from electrical transients and common-mode noise inherent in high-power excitation systems. Firmware compatibility allows for integrated management of the 4-20 mA input and 0-5 V output signal ranges.\u003c\/p\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cp\u003eQ: Can this module be hot-swapped while the EX2100 system is in operation?\u003c\/p\u003e\n\u003cp\u003eA: No, this module must not be installed or removed while the rack power is active. Doing so can cause logic corruption on the backplane or damage the Ethernet transceiver interfaces.\u003c\/p\u003e\n\u003cp\u003eQ: How is the 1500 V RMS isolation maintained during field wiring?\u003c\/p\u003e\n\u003cp\u003eA: Isolation is maintained by the physical design of the board's internal circuitry. To ensure this rating is effective, field wiring must be routed separately from high-voltage AC cables, and shield drain wires must be terminated to a clean chassis ground.\u003c\/p\u003e\n\u003ch3\u003eField Installation Guidelines\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003ePower down the excitation control rack and verify that all power rails are at 0 VDC.\u003c\/li\u003e\n\u003cli\u003eVerify the slot configuration within the rack to ensure the backplane connector matches the IS200ERIOH1ABC pinout.\u003c\/li\u003e\n\u003cli\u003eAlign the module with the chassis guide rails and slide it into the rack until the backplane connector is fully seated.\u003c\/li\u003e\n\u003cli\u003eSecure the module using the front-panel captive screws to ensure physical stability and proper electrical grounding to the chassis.\u003c\/li\u003e\n\u003cli\u003eConnect the dual Ethernet cables to the module ports; ensure that the cable bend radius is respected to prevent signal degradation and maintain 100 MB link integrity.\u003c\/li\u003e\n\u003c\/ol\u003e","brand":"GE FANUC","offers":[{"title":"Default Title","offer_id":52468929298744,"sku":"IS200ERIOH1ABC","price":220.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0893\/1616\/3896\/files\/IS200ERIOH1ABC1.jpg?v=1780560039","url":"https:\/\/www.automodulexpert.com\/id\/products\/is200erioh1abc-general-electric-i-o-regulator-module-new-original-stock","provider":"AutoModuleXpert Ltd.","version":"1.0","type":"link"}