{"product_id":"discrete-terminal-board-ge-fanuc-ds200dtbdg1aaa","title":"Discrete Terminal Board GE FANUC DS200DTBDG1AAA","description":"\u003cp\u003eConfigured for discrete signal termination in Mark V control system architectures, the \u003cstrong\u003eGE FANUC DS200DTBDG1AAA\u003c\/strong\u003e (\u003cstrong\u003eDS200DTBDG1\u003c\/strong\u003e Discrete Terminal Board) provides direct physical signal distribution for turbine discrete input and output circuits. This component serves as the primary interface between field-mounted instrumentation and the Mark V I\/O packs, ensuring deterministic signal routing across the control network.\u003c\/p\u003e\n\u003ch3\u003eHardware Specifications\u003c\/h3\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003e\u003cstrong\u003eParameter\u003c\/strong\u003e\u003c\/th\u003e\n\u003cth\u003e\u003cstrong\u003eSpecification\u003c\/strong\u003e\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eModel\u003c\/td\u003e\n\u003ctd\u003eDS200DTBDG1AAA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBrand\u003c\/td\u003e\n\u003ctd\u003eGE FANUC\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOrigin\u003c\/td\u003e\n\u003ctd\u003eUnited States\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWeight\u003c\/td\u003e\n\u003ctd\u003e0.60 kg\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDimensions\u003c\/td\u003e\n\u003ctd\u003e25.0 cm x 10.0 cm x 8.0 cm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOperating Temp\u003c\/td\u003e\n\u003ctd\u003e-30 deg C to +65 deg C\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePower Consumption\u003c\/td\u003e\n\u003ctd\u003ePassive signal distribution\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSignal Voltage\u003c\/td\u003e\n\u003ctd\u003e28 VDC nominal\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eVoltage Range\u003c\/td\u003e\n\u003ctd\u003e18 VDC to 32 VDC\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eChannel Capacity\u003c\/td\u003e\n\u003ctd\u003e24 discrete points\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eCurrent Rating\u003c\/td\u003e\n\u003ctd\u003e2.0 A per terminal\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eMounting Style\u003c\/td\u003e\n\u003ctd\u003eDIN-rail or panel mount\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003ch3\u003eBackplane Bus Communication and Signal Isolation\u003c\/h3\u003e\n\u003cp\u003eThe DS200DTBDG1AAA utilizes dual 50-pin female connectors to facilitate deterministic communication with the Mark V I\/O packs. This hardware ensures signal integrity through galvanic isolation rated at 500 VAC RMS channel-to-ground, protecting the control logic from field-level transient voltages. Firmware flash compatibility is managed at the I\/O pack level; however, the terminal board must maintain precise impedance paths to prevent signal latency during discrete state transitions.\u003c\/p\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cp\u003eQ: Does the terminal board support hot-swapping under load?\u003c\/p\u003e\n\u003cp\u003eA: No. The DS200DTBDG1AAA is not designed for hot-swapping. The system must be de-energized to prevent damage to the dual 50-pin connectors and the associated backplane circuitry.\u003c\/p\u003e\n\u003cp\u003eQ: What is the maximum torque allowed for the screw terminal blocks?\u003c\/p\u003e\n\u003cp\u003eA: The terminal screws are rated for a maximum torque of 0.5 Nm. Exceeding this value may strip the threads or damage the integrity of the terminal block housing.\u003c\/p\u003e\n\u003cp\u003eQ: Can this board be used for high-voltage switching applications?\u003c\/p\u003e\n\u003cp\u003eA: No. The board is rated for 28 VDC nominal operation. It is strictly limited to low-voltage discrete input and output signals within the 18 VDC to 32 VDC range.\u003c\/p\u003e\n\u003ch3\u003eField Installation Guidelines\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003eVerify that the power supply to the turbine discrete circuits is isolated.\u003c\/li\u003e\n\u003cli\u003eSecure the board to the DIN-rail or mounting panel using all four M4 screw holes to ensure mechanical stability.\u003c\/li\u003e\n\u003cli\u003eUtilize stranded copper wire between 12 AWG and 24 AWG for field connections.\u003c\/li\u003e\n\u003cli\u003eStrip insulation to the minimum required length and tighten terminal screws to 0.5 Nm.\u003c\/li\u003e\n\u003cli\u003eAlign the dual 50-pin connectors carefully with the I\/O pack to avoid bending the contact pins.\u003c\/li\u003e\n\u003cli\u003eConfirm that the input voltage remains within the 18 VDC to 32 VDC range before initiating system startup.\u003c\/li\u003e\n\u003c\/ol\u003e","brand":"GE FANUC","offers":[{"title":"Default Title","offer_id":52620070519096,"sku":"DS200DTBDG1AAA","price":220.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0893\/1616\/3896\/files\/DS200DTBDG1AAA.jpg?v=1783497528","url":"https:\/\/www.automodulexpert.com\/products\/discrete-terminal-board-ge-fanuc-ds200dtbdg1aaa","provider":"AutoModuleXpert Ltd.","version":"1.0","type":"link"}