{"product_id":"ds200rtbag1ahc-relay-terminal-board-general-electric","title":"DS200RTBAG1AHC Relay Terminal Board General Electric","description":"\u003cp\u003eConfigured for signal relay and termination management in Mark V turbine control systems, the \u003cstrong\u003eGeneral Electric DS200RTBAG1AHC\u003c\/strong\u003e (\u003cstrong\u003eDS200RTBAG1AHC\u003c\/strong\u003e Relay Terminal Board) provides direct physical\/electrical execution.\u003c\/p\u003e\n\u003ch3\u003eHardware Specifications\u003c\/h3\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003e\u003cstrong\u003eParameter\u003c\/strong\u003e\u003c\/th\u003e\n\u003cth\u003e\u003cstrong\u003eSpecification\u003c\/strong\u003e\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eModel\u003c\/td\u003e\n\u003ctd\u003eDS200RTBAG1AHC\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBrand\u003c\/td\u003e\n\u003ctd\u003eGeneral Electric\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOrigin\u003c\/td\u003e\n\u003ctd\u003eUSA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWeight\u003c\/td\u003e\n\u003ctd\u003e0.5 kg\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDimensions\u003c\/td\u003e\n\u003ctd\u003e33 cm x 10 cm x 5 cm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOperating Temp\u003c\/td\u003e\n\u003ctd\u003eNot specified\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePower Consumption\u003c\/td\u003e\n\u003ctd\u003eNot specified\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eCore Function\u003c\/td\u003e\n\u003ctd\u003eRelay signal termination\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003ch3\u003eProfinet \/ EtherNet\/IP Deterministic Networks\u003c\/h3\u003e\n\u003cp\u003eThe \u003cstrong\u003eGeneral Electric DS200RTBAG1AHC\u003c\/strong\u003e serves as the primary interface for relay control signals within the Mark V backplane architecture. The board ensures deterministic signal propagation between the controller and field-level relay devices. Firmware flash compatibility is managed through the terminal board's integration with the primary Mark V controller; improper matching of board revision levels can result in I\/O scanning latency or register mapping errors. The hardware is designed to handle high-density relay connections, requiring precise backplane communication velocity to maintain synchronization across the control network during high-speed switching operations.\u003c\/p\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cp\u003eQ: Can the DS200RTBAG1AHC be replaced while the control rack is powered?\u003c\/p\u003e\n\u003cp\u003eA: No. The board must be de-energized by isolating the control rack power supply and disconnecting all field signal cabling to prevent short circuits on the backplane bus during physical handling.\u003c\/p\u003e\n\u003cp\u003eQ: Are there specific torque requirements for the terminal connections?\u003c\/p\u003e\n\u003cp\u003eA: Connections should be tightened according to standard industrial torque specifications for the wire gauge used to ensure low-resistance contact and prevent thermal degradation of the terminal blocks under load.\u003c\/p\u003e\n\u003ch3\u003eField Installation Guidelines\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eMounting\u003c\/strong\u003e: The board is designed for mounting within the standard Mark V cabinet chassis. Ensure all mounting hardware is tightened to establish a solid ground bond between the board and the cabinet rail.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWiring\u003c\/strong\u003e: Route relay signal wiring separately from high-voltage AC power lines to prevent induced electromagnetic interference. Use shielded cables for all sensitive instrumentation signals.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGrounding\u003c\/strong\u003e: Terminate cable shields at the designated chassis grounding studs to minimize ground loop currents across the terminal board.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eEnvironmental\u003c\/strong\u003e: Although physical dimensions are compact, ensure no obstructions block the airflow over the terminal surface to allow for heat dissipation during sustained relay actuation.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"GE FANUC","offers":[{"title":"Default Title","offer_id":52596470415672,"sku":"DS200RTBAG1AHC","price":220.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0893\/1616\/3896\/files\/DS200RTBAG1AHC2.jpg?v=1782980867","url":"https:\/\/www.automodulexpert.com\/products\/ds200rtbag1ahc-relay-terminal-board-general-electric","provider":"AutoModuleXpert Ltd.","version":"1.0","type":"link"}