{"product_id":"ds200sdcig1agb-ge-dc-power-supply-and-instrumentation-board","title":"DS200SDCIG1AGB GE DC Power Supply and Instrumentation Board","description":"\u003cp\u003eConfigured for power distribution and sensor signal conditioning in Mark V turbine control platforms, the \u003cstrong\u003eGE DS200SDCIG1AGB\u003c\/strong\u003e (\u003cstrong\u003eDS200SDCI\u003c\/strong\u003e DC Power Supply and Instrumentation Board) provides direct electrical regulation and instrumentation monitoring.\u003c\/p\u003e\n\u003ch3\u003eHardware Specifications\u003c\/h3\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003e\u003cstrong\u003eParameter\u003c\/strong\u003e\u003c\/th\u003e\n\u003cth\u003e\u003cstrong\u003eSpecification\u003c\/strong\u003e\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eModel\u003c\/td\u003e\n\u003ctd\u003eDS200SDCIG1AGB\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBrand\u003c\/td\u003e\n\u003ctd\u003eGE (General Electric)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOrigin\u003c\/td\u003e\n\u003ctd\u003eUSA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWeight\u003c\/td\u003e\n\u003ctd\u003e0.57kg\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDimensions\u003c\/td\u003e\n\u003ctd\u003eStandard Mark V PCB Form Factor\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOperating Temp\u003c\/td\u003e\n\u003ctd\u003e0 to 60 deg C\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePower Consumption\u003c\/td\u003e\n\u003ctd\u003eDependent on backplane load\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eFunctional Series\u003c\/td\u003e\n\u003ctd\u003eMark V \/ DC2000\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eRevisions\u003c\/td\u003e\n\u003ctd\u003eFunctional Rev A, Functional Rev G, Artwork Rev B\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003ch3\u003eProfinet \/ EtherNet\/IP Deterministic Networks and Backplane Communication\u003c\/h3\u003e\n\u003cp\u003eThe DS200SDCIG1AGB utilizes a backplane bus interface to maintain data integrity across the Mark V controller architecture. Communication velocity and signal processing are managed through local bus synchronization, ensuring deterministic exchange between the power supply circuitry and the main processor modules. Firmware flash compatibility is limited to the specific revision hardware, necessitating alignment with existing Mark V control software versions to prevent bus contention or signal latency during turbine operation.\u003c\/p\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cp\u003eQ: Does the DS200SDCIG1AGB support hot-swap operations in a live Mark V rack?\u003c\/p\u003e\n\u003cp\u003eA: No. The board lacks integrated hot-swap protection circuitry. Power must be isolated from the specific slot on the backplane before insertion or removal to prevent electrical arcing or damage to the backplane pins.\u003c\/p\u003e\n\u003cp\u003eQ: How should the auxiliary power inputs be verified before full system commissioning?\u003c\/p\u003e\n\u003cp\u003eA: Validate the input voltage levels against the DC2000 subseries requirements using a calibrated multimeter. Ensure the common reference point is isolated from earth ground unless specified by the system grounding scheme to prevent ground loops within the instrumentation signal paths.\u003c\/p\u003e\n\u003ch3\u003eField Installation Guidelines\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eEnsure all personnel adhere to ESD (Electrostatic Discharge) safety protocols, utilizing grounded wrist straps during handling.\u003c\/li\u003e\n\u003cli\u003ePrior to installation, inspect the backplane connectors for debris or oxidation.\u003c\/li\u003e\n\u003cli\u003eAlign the board with the card cage guide rails; ensure full engagement with the backplane connector before tightening the front panel retention screws.\u003c\/li\u003e\n\u003cli\u003eRoute signal cables away from high-current power cables to minimize electromagnetic interference (EMI).\u003c\/li\u003e\n\u003cli\u003eVerify that the hardware revision (Functional Rev A\/G, Artwork Rev B) matches the requirements defined in document GEI-100173.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"GE FANUC","offers":[{"title":"Default Title","offer_id":52599954538808,"sku":"DS200SDCIG1AGB","price":220.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0893\/1616\/3896\/files\/DS200SDCIG1AGB.jpg?v=1783066768","url":"https:\/\/www.automodulexpert.com\/products\/ds200sdcig1agb-ge-dc-power-supply-and-instrumentation-board","provider":"AutoModuleXpert Ltd.","version":"1.0","type":"link"}