{"product_id":"ds200tccbg3b-common-extended-analog-i-o-board-ge","title":"DS200TCCBG3B Common Extended Analog I\/O Board GE","description":"\u003cp\u003eThe \u003cstrong\u003eGE DS200TCCBG3B\u003c\/strong\u003e, also cataloged as the \u003cstrong\u003eDS200TCCBG3\u003c\/strong\u003e Common Extended Analog I\/O Board, operates as a dedicated hardware component for analog signal conditioning and I\/O expansion within Mark V turbine control systems. The board provides direct physical interface points to facilitate the precise transition between field sensors and internal control logic.\u003c\/p\u003e\n\u003ch3\u003eHardware Specifications\u003c\/h3\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003e\u003cstrong\u003eParameter\u003c\/strong\u003e\u003c\/th\u003e\n\u003cth\u003e\u003cstrong\u003eSpecification\u003c\/strong\u003e\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eModel\u003c\/td\u003e\n\u003ctd\u003eDS200TCCBG3B\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBrand\u003c\/td\u003e\n\u003ctd\u003eGeneral Electric\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOrigin\u003c\/td\u003e\n\u003ctd\u003eUSA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWeight\u003c\/td\u003e\n\u003ctd\u003e0.7 kg\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDimensions\u003c\/td\u003e\n\u003ctd\u003e102.2 cm x 12.4 cm x 12.6 cm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOperating Temp\u003c\/td\u003e\n\u003ctd\u003e0 deg C to 60 deg C\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePower Consumption\u003c\/td\u003e\n\u003ctd\u003eBackplane supplied\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eModule Type\u003c\/td\u003e\n\u003ctd\u003eCommon Extended Analog I\/O\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003ch3\u003eIndustrial Control Backplane Integration\u003c\/h3\u003e\n\u003cp\u003eThe \u003cstrong\u003eGE DS200TCCBG3B\u003c\/strong\u003e integrates with the Mark V architecture to maintain signal integrity during extended analog I\/O processing. The board manages backplane bus communication velocity by providing low-impedance pathways for analog control loops. Proper firmware flash compatibility is required when integrating this board into updated control racks to ensure that the module correctly maps input\/output registers. Deterministic data transfer is maintained through the module's high-density interface, which requires strict adherence to signal synchronization parameters defined by the host controller.\u003c\/p\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cp\u003eQ: Is this board capable of hot-swapping during normal turbine control operation?\u003c\/p\u003e\n\u003cp\u003eA: No. The Mark V backplane connector interface is not designed for hot-swapping. The system must be de-energized to prevent electrical shorts or backplane damage during installation or removal.\u003c\/p\u003e\n\u003cp\u003eQ: What precautions are necessary when wiring the extended analog I\/O?\u003c\/p\u003e\n\u003cp\u003eA: Ensure that all field wiring is properly seated into the terminal blocks. Shielded cabling must be used for all analog signal paths, and the drain wires should be terminated to the designated ground bus to suppress electromagnetic interference.\u003c\/p\u003e\n\u003ch3\u003eField Installation Guidelines\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003ePower De-energization: Verify the control rack is completely isolated from the power source before commencing any physical hardware work.\u003c\/li\u003e\n\u003cli\u003eRack Mounting: Align the board with the specified rack position. Ensure the mounting screws are tightened to provide sufficient mechanical stability and electrical contact with the chassis frame.\u003c\/li\u003e\n\u003cli\u003eWiring Termination: Attach field signal wires to the terminal points. Ensure that wire insulation is not trapped under the terminals to prevent intermittent connection failures.\u003c\/li\u003e\n\u003cli\u003eGrounding: Connect the board's chassis grounding point to the system earth ground using an appropriate gauge wire to minimize noise and surge vulnerability.\u003c\/li\u003e\n\u003cli\u003eVerification: Upon re-energizing the rack, confirm that the I\/O mapping software reflects the presence of the board and that no communication fault codes are triggered in the control interface.\u003c\/li\u003e\n\u003c\/ol\u003e","brand":"GE FANUC","offers":[{"title":"Default Title","offer_id":52600003428664,"sku":"DS200TCCBG3B","price":220.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0893\/1616\/3896\/files\/DS200TCCBG3B2.jpg?v=1783066771","url":"https:\/\/www.automodulexpert.com\/products\/ds200tccbg3b-common-extended-analog-i-o-board-ge","provider":"AutoModuleXpert Ltd.","version":"1.0","type":"link"}