{"product_id":"ds200tcpdg2b-power-distribution-board-general-electric","title":"DS200TCPDG2B Power Distribution Board General Electric","description":"\u003cp\u003eConfigured for power signal routing and bus management in Mark V control platforms, the \u003cstrong\u003eGeneral Electric DS200TCPDG2B\u003c\/strong\u003e (\u003cstrong\u003eDS200TCPDG2B\u003c\/strong\u003e Power Distribution Board) provides direct physical\/electrical execution for distributing regulated voltage levels across peripheral interface modules.\u003c\/p\u003e\n\u003ch3\u003eHardware Specifications\u003c\/h3\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003e\u003cstrong\u003eParameter\u003c\/strong\u003e\u003c\/th\u003e\n\u003cth\u003e\u003cstrong\u003eSpecification\u003c\/strong\u003e\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eModel\u003c\/td\u003e\n\u003ctd\u003eDS200TCPDG2B\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBrand\u003c\/td\u003e\n\u003ctd\u003eGeneral Electric\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOrigin\u003c\/td\u003e\n\u003ctd\u003eUSA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWeight\u003c\/td\u003e\n\u003ctd\u003e0.8 kg\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDimensions\u003c\/td\u003e\n\u003ctd\u003e14.75 cm x 9.50 cm x 3.50 cm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOperating Temp\u003c\/td\u003e\n\u003ctd\u003e0 to 60 deg C\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePower Consumption\u003c\/td\u003e\n\u003ctd\u003eDefined by system bus load\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePrimary Function\u003c\/td\u003e\n\u003ctd\u003ePower distribution and bus regulation\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003ch3\u003eProfinet \/ EtherNet\/IP Deterministic Networks\u003c\/h3\u003e\n\u003cp\u003eThe DS200TCPDG2B maintains electrical stability across deterministic control networks by regulating incoming supply voltages before they reach backplane-mounted components. The board's circuit topology prevents voltage spikes and surges from propagating through the backplane bus, ensuring consistent power delivery. This stability is required for maintaining the deterministic communication velocity of connected I\/O modules, as power fluctuations could otherwise introduce jitter or signal degradation within the high-speed data bus.\u003c\/p\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cp\u003eQ: Is this board capable of hot-swap operations?\u003c\/p\u003e\n\u003cp\u003eA: No, the DS200TCPDG2B does not support hot-swapping. The system rack must be fully de-energized and verified with a multimeter before attempting to remove or install the board to avoid damaging the backplane connectors.\u003c\/p\u003e\n\u003cp\u003eQ: What are the primary indicators of a board failure during operation?\u003c\/p\u003e\n\u003cp\u003eA: Failure is typically characterized by a loss of power to downstream modules or the tripping of integrated supply monitoring circuits. If these symptoms occur, verify input voltage levels at the terminal connections before replacing the module.\u003c\/p\u003e\n\u003ch3\u003eField Installation Guidelines\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003ePower down the entire control rack and perform a lockout\/tagout procedure to ensure no voltage is present.\u003c\/li\u003e\n\u003cli\u003eCarefully align the board with the rack card guides, ensuring the backplane interface pins are not obstructed.\u003c\/li\u003e\n\u003cli\u003eSlide the board into the slot until the DIN connector is fully seated. Do not apply excessive force.\u003c\/li\u003e\n\u003cli\u003eSecure the module to the rack chassis using the provided mounting screws to maintain a consistent ground path.\u003c\/li\u003e\n\u003cli\u003eInspect all power distribution cabling to ensure they are firmly terminated and that no shielding is touching exposed conductors.\u003c\/li\u003e\n\u003cli\u003eVerify cabinet temperatures are within the 0 to 60 deg C range prior to restoring power to the system.\u003c\/li\u003e\n\u003c\/ol\u003e","brand":"GE FANUC","offers":[{"title":"Default Title","offer_id":52592668672312,"sku":"DS200TCPDG2B","price":220.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0893\/1616\/3896\/files\/DS200TCPDG2B2.jpg?v=1782892600","url":"https:\/\/www.automodulexpert.com\/products\/ds200tcpdg2b-power-distribution-board-general-electric","provider":"AutoModuleXpert Ltd.","version":"1.0","type":"link"}