{"product_id":"ge-is200ehprg1ccb-mark-vi-exciter-collector-board","title":"GE IS200EHPRG1CCB Mark VI Exciter Collector Board","description":"\u003ch2\u003eGE IS200EHPRG1CCB Mark VI Exciter Collector Board\u003c\/h2\u003e\n\u003cp\u003eThe \u003cstrong\u003eGE IS200EHPRG1CCB\u003c\/strong\u003e, also cataloged as the \u003cstrong\u003eIS200EHPRG1C\u003c\/strong\u003e Exciter Collector Board, operates as a dedicated hardware component for receiving logic-level gate pulse signals from the EMIO board and distributing them to EGPA exciter gate pulse amplifier boards within GE Mark VI Speedtronic turbine control platforms.\u003c\/p\u003e\n\u003ch3\u003eHardware Specifications\u003c\/h3\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003e\u003cstrong\u003eParameter\u003c\/strong\u003e\u003c\/th\u003e\n\u003cth\u003e\u003cstrong\u003eSpecification\u003c\/strong\u003e\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eModel\u003c\/td\u003e\n\u003ctd\u003eIS200EHPRG1CCB\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBrand\u003c\/td\u003e\n\u003ctd\u003eGE Fanuc \/ General Electric\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOrigin\u003c\/td\u003e\n\u003ctd\u003eUSA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWeight\u003c\/td\u003e\n\u003ctd\u003e0.3 kg\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDimensions\u003c\/td\u003e\n\u003ctd\u003e100 mm x 80 mm x 20 mm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOperating Temp\u003c\/td\u003e\n\u003ctd\u003e-40 to +70 deg C\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePower Supply Input\u003c\/td\u003e\n\u003ctd\u003e24 VDC\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eCommunication Protocol\u003c\/td\u003e\n\u003ctd\u003eModbus TCP\/IP\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBoard Type\u003c\/td\u003e\n\u003ctd\u003eExciter Collector PCB Assembly\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSystem Architecture\u003c\/td\u003e\n\u003ctd\u003eMark VI Speedtronic Turbine Control System\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003ch3\u003eBackplane Bus Communication \u0026amp; I\/O Density Scaling\u003c\/h3\u003e\n\u003cp\u003eThe IS200EHPRG1CCB module processes high-speed gate driver signals across the exciter subrack assembly. Internal signal routes maintain high backplane bus communication velocity, minimizing propagation delay during pulse routing between main controller cards and gate power amplifiers. Diagnostic logic monitors internal supply rails and pulse paths, triggering onboard fault LEDs and transmitting diagnostic status flags over Modbus TCP\/IP network interfaces. High I\/O density scaling and firmware flash compatibility allow the card to interface seamlessly across redundant Mark VI control architectures without signal distortion.\u003c\/p\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cp\u003eQ: What is the primary functional role of the IS200EHPRG1CCB within the static excitation subsystem?\u003c\/p\u003e\n\u003cp\u003eA: The board functions as an intermediate pulse distributor, accepting logic-level firing commands from the main control interface (EMIO) and fanning them out to driver amplifiers (EGPA) that fire the thyristor bridge.\u003c\/p\u003e\n\u003cp\u003eQ: How does the module indicate active hardware or communication fault conditions?\u003c\/p\u003e\n\u003cp\u003eA: Onboard diagnostic LEDs indicate power status and channel fault states directly on the front plate, while internal registers broadcast detailed hardware diagnostic flags over Modbus TCP\/IP.\u003c\/p\u003e\n\u003ch3\u003eField Installation Guidelines\u003c\/h3\u003e\n\u003cp\u003eMount the IS200EHPRG1CCB PCB into its designated card slot within the Mark VI panel enclosure. Ensure the mounting chassis connects to the main enclosure ground plane to prevent static charge accumulation across the board trace layers.\u003c\/p\u003e\n\u003cp\u003eConnect the 24 VDC power feed wires to the designated terminal block, ensuring correct polarity prior to system energization. Shield all signal ribbon cables and Modbus TCP\/IP network links, grounding cable drain wires at the panel earth bar to reduce electromagnetic interference (EMI) generated by switching thyristor power circuits.\u003c\/p\u003e","brand":"GE FANUC","offers":[{"title":"Default Title","offer_id":51224569708856,"sku":"IS200EHPRG1CCB","price":188.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0893\/1616\/3896\/files\/IS200EHPRG1CCB.jpg?v=1760145424","url":"https:\/\/www.automodulexpert.com\/products\/ge-is200ehprg1ccb-mark-vi-exciter-collector-board","provider":"AutoModuleXpert Ltd.","version":"1.0","type":"link"}