{"product_id":"general-electric-ds200tcpsg1ape-dc-input-power-supply","title":"General Electric DS200TCPSG1APE DC Input Power Supply","description":"\u003cp\u003eConfigured for power conversion within industrial control networks, the \u003cstrong\u003eGeneral Electric DS200TCPSG1APE\u003c\/strong\u003e (\u003cstrong\u003eDS200TCPSG1APE\u003c\/strong\u003e DC Input Power Supply) provides direct physical and electrical execution of voltage regulation for system backplane operations.\u003c\/p\u003e\n\u003ch3\u003eHardware Specifications\u003c\/h3\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003e\u003cstrong\u003eParameter\u003c\/strong\u003e\u003c\/th\u003e\n\u003cth\u003e\u003cstrong\u003eSpecification\u003c\/strong\u003e\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eModel\u003c\/td\u003e\n\u003ctd\u003eDS200TCPSG1APE\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBrand\u003c\/td\u003e\n\u003ctd\u003eGeneral Electric\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOrigin\u003c\/td\u003e\n\u003ctd\u003eUSA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWeight\u003c\/td\u003e\n\u003ctd\u003e1.2 kg\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDimensions\u003c\/td\u003e\n\u003ctd\u003e27.8 cm x 21.2 cm x 6.5 cm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOperating Temp\u003c\/td\u003e\n\u003ctd\u003e0 deg C to 60 deg C\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePower Consumption\u003c\/td\u003e\n\u003ctd\u003eDependent on backplane bus load\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eInput Type\u003c\/td\u003e\n\u003ctd\u003eDC Input\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003ch3\u003eBackplane Bus and Firmware Compatibility\u003c\/h3\u003e\n\u003cp\u003eThe \u003cstrong\u003eGeneral Electric DS200TCPSG1APE\u003c\/strong\u003e serves as an integrated component within the control rack architecture, requiring established backplane bus communication velocity to ensure consistent power delivery to peripheral I\/O modules. Firmware flash compatibility is dictated by the master processor module versioning; installers must confirm that the host backplane revision supports the specified power profile of the \u003cstrong\u003eDS200TCPSG1APE\u003c\/strong\u003e. Load management and I\/O density scaling must be calculated according to the system power budget to prevent thermal overload on the control rack backplane.\u003c\/p\u003e\n\u003ch3\u003eFrequently Asked Questions (FAQ)\u003c\/h3\u003e\n\u003cp\u003eQ: Does this power supply module support hot-swapping during system operation?\u003c\/p\u003e\n\u003cp\u003eA: Hot-swapping is not supported. The control rack must be de-energized to prevent electrical arcing or damage to backplane connector pins during installation or removal.\u003c\/p\u003e\n\u003cp\u003eQ: How is the backplane bus communication synchronized with the power distribution?\u003c\/p\u003e\n\u003cp\u003eA: Synchronization is maintained through the rack backplane interfaces, which facilitate power distribution and diagnostic signaling between the supply module and the system controller.\u003c\/p\u003e\n\u003ch3\u003eField Installation Guidelines\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003e\n\u003cstrong\u003ePreparation\u003c\/strong\u003e: Ensure the control rack is isolated from the main power source. Verify the slot configuration for the power supply unit.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eInsertion\u003c\/strong\u003e: Align the module with the designated rack guides. Slide the unit until the backplane connectors are fully engaged.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMechanical Fastening\u003c\/strong\u003e: Tighten the module faceplate screws to the rack frame to ensure structural stability and reliable chassis grounding.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWiring\u003c\/strong\u003e: Connect input DC power cables to the terminal block, ensuring correct polarity. Verify wire gauge meets the current-carrying requirements of the system load.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eShielding\u003c\/strong\u003e: Ensure all signal cables are properly shielded and grounded at the cabinet entry points to minimize electromagnetic interference.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eInspection\u003c\/strong\u003e: Perform a final continuity check on the DC input lines before restoring system power.\u003c\/li\u003e\n\u003c\/ol\u003e","brand":"GE FANUC","offers":[{"title":"Default Title","offer_id":52570044498232,"sku":"DS200TCPSG1APE","price":220.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0893\/1616\/3896\/files\/DS200TCPSG1APE.jpg?v=1782459405","url":"https:\/\/www.automodulexpert.com\/products\/general-electric-ds200tcpsg1ape-dc-input-power-supply","provider":"AutoModuleXpert Ltd.","version":"1.0","type":"link"}