{"product_id":"general-electric-is200tbaih1c-dc-analog-terminal-board","title":"General Electric IS200TBAIH1C DC Analog Terminal Board","description":"\u003cp\u003eThe \u003cstrong\u003eGeneral Electric IS200TBAIH1C DC\u003c\/strong\u003e, also cataloged as the \u003cstrong\u003eIS200TBAIH1C\u003c\/strong\u003e Analog Terminal Board, operates as a dedicated hardware component for analog signal termination within Mark VI turbine control system architectures.\u003c\/p\u003e\n\u003ch3\u003eHardware Specifications\u003c\/h3\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003e\u003cstrong\u003eParameter\u003c\/strong\u003e\u003c\/th\u003e\n\u003cth\u003e\u003cstrong\u003eSpecification\u003c\/strong\u003e\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eModel\u003c\/td\u003e\n\u003ctd\u003eIS200TBAIH1C DC\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBrand\u003c\/td\u003e\n\u003ctd\u003eGeneral Electric\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOrigin\u003c\/td\u003e\n\u003ctd\u003eUSA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWeight\u003c\/td\u003e\n\u003ctd\u003e0.22 kg\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDimensions\u003c\/td\u003e\n\u003ctd\u003e3.8 cm x 11.5 cm x 4.5 cm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOperating Temp\u003c\/td\u003e\n\u003ctd\u003e-30 to 65 deg C\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePower Consumption\u003c\/td\u003e\n\u003ctd\u003ePassive (N\/A)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSignal Interface\u003c\/td\u003e\n\u003ctd\u003eAnalog terminal block\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003ch3\u003eProcess Control and Signal Integrity\u003c\/h3\u003e\n\u003cp\u003eThe \u003cstrong\u003eIS200TBAIH1C DC\u003c\/strong\u003e serves as the primary interface for field-side analog instrumentation, facilitating direct wire-to-system termination for 4-20 mA loops. This terminal board is configured to provide channel-to-channel isolation when utilized with compatible I\/O packs, preventing ground loops and common-mode noise propagation. Signal conditioning is not performed at this hardware level; instead, the board maintains electrical continuity for HART protocol signals, ensuring that impedance characteristics remain within specified limits for analog loop stability.\u003c\/p\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cp\u003eQ: Is this board compatible with firmware-based diagnostic functions?\u003c\/p\u003e\n\u003cp\u003eA: No. The IS200TBAIH1C DC is a passive terminal board without onboard processors or firmware. Diagnostic capabilities for analog loops are executed by the upstream I\/O pack connected to this terminal board.\u003c\/p\u003e\n\u003cp\u003eQ: Can this terminal board be used in a redundant I\/O configuration?\u003c\/p\u003e\n\u003cp\u003eA: Yes, provided the backplane and I\/O pack configuration in the Mark VI cabinet supports redundant input paths. The terminal board itself provides the necessary physical connection points to bridge field signals to redundant control modules.\u003c\/p\u003e\n\u003ch3\u003eField Installation Guidelines\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003e\n\u003cstrong\u003eTerminal Connections:\u003c\/strong\u003e Insert field wiring into the screw terminal blocks. Ensure a torque setting of 0.5 Nm is applied to prevent loose connections, which may manifest as intermittent signal noise in the DCS.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eShielding:\u003c\/strong\u003e Terminate cable shields to the provided grounding bar on the terminal board. Ensure the shield is only grounded at one point in the circuit to avoid creating ground loops.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMounting:\u003c\/strong\u003e Secure the board to the vertical mounting plate in the control cabinet. Ensure adequate clearance for cable dressing and heat dissipation if the board is situated near high-density power components.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWiring Segregation:\u003c\/strong\u003e Maintain physical separation between analog signal wiring and high-voltage AC lines to satisfy electromagnetic compatibility requirements and prevent signal interference.\u003c\/li\u003e\n\u003c\/ol\u003e","brand":"GE FANUC","offers":[{"title":"Default Title","offer_id":52551204143416,"sku":"IS200TBAIH1C DC","price":220.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0893\/1616\/3896\/files\/IS200TBAIH1C_CC1.jpg?v=1782199907","url":"https:\/\/www.automodulexpert.com\/products\/general-electric-is200tbaih1c-dc-analog-terminal-board","provider":"AutoModuleXpert Ltd.","version":"1.0","type":"link"}