{"product_id":"is200biclh1aed-general-electric-bridge-interface-card-new-stock","title":"IS200BICLH1AED General Electric Bridge Interface Card | New Stock","description":"\u003cp\u003eThe \u003cstrong\u003eGeneral Electric IS200BICLH1AED\u003c\/strong\u003e, also cataloged as the \u003cstrong\u003eIS200BICLH1\u003c\/strong\u003e Bridge Interface Card, operates as a dedicated hardware component for signal routing and data bus interfacing within Mark VI turbine control platforms.\u003c\/p\u003e\n\u003ch3\u003eHardware Specifications\u003c\/h3\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003e\u003cstrong\u003eParameter\u003c\/strong\u003e\u003c\/th\u003e\n\u003cth\u003e\u003cstrong\u003eSpecification\u003c\/strong\u003e\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eModel\u003c\/td\u003e\n\u003ctd\u003eIS200BICLH1AED\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBrand\u003c\/td\u003e\n\u003ctd\u003eGeneral Electric\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOrigin\u003c\/td\u003e\n\u003ctd\u003eUSA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWeight\u003c\/td\u003e\n\u003ctd\u003e1.5 kg\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDimensions\u003c\/td\u003e\n\u003ctd\u003e267 mm x 165 mm x 32 mm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOperating Temp\u003c\/td\u003e\n\u003ctd\u003e0 to 60 deg C\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePower Consumption\u003c\/td\u003e\n\u003ctd\u003e18 W (Typical)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eMounting Type\u003c\/td\u003e\n\u003ctd\u003eVME Rack Bus\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eInterface\u003c\/td\u003e\n\u003ctd\u003eBridge Communications \/ Backplane\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003ch3\u003eProfinet \/ EtherNet\/IP Deterministic Networks\u003c\/h3\u003e\n\u003cp\u003eThe IS200BICLH1AED serves as the primary gateway for data transfer between the bridge control module and the backplane deterministic network. It manages the flow of control signals and status data, ensuring high-speed synchronization across the turbine control system. The card utilizes advanced bus arbitration to maintain deterministic communication timing, which is vital for maintaining stability in turbine regulation. Firmware flash compatibility enables the board to accept logic updates that adapt the interface to changing control requirements without requiring physical hardware modifications.\u003c\/p\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cp\u003eQ: Does the IS200BICLH1AED support hot-swapping within the VME rack?\u003c\/p\u003e\n\u003cp\u003eA: No. Removing or inserting this module while the backplane is powered can cause electrical arcs or communication faults, leading to a system trip. Power must be isolated before performing any maintenance.\u003c\/p\u003e\n\u003cp\u003eQ: How can I verify that the board is communicating correctly with the controller?\u003c\/p\u003e\n\u003cp\u003eA: Status indicators on the front panel provide real-time feedback on backplane communication health. A steady \"OK\" LED status indicates successful initialization and proper synchronization with the control rack master.\u003c\/p\u003e\n\u003ch3\u003eField Installation Guidelines\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003eConfirm that the rack power is in the OFF state before attempting to insert the module.\u003c\/li\u003e\n\u003cli\u003eCarefully align the card with the designated VME slot guides to avoid pin damage on the backplane connector.\u003c\/li\u003e\n\u003cli\u003eApply steady pressure until the module is fully seated, then tighten the faceplate captive screws to secure the unit and complete the chassis ground path.\u003c\/li\u003e\n\u003cli\u003eIf connecting external bridge cabling, ensure the connectors are keyed properly and locked to prevent intermittent signal loss.\u003c\/li\u003e\n\u003cli\u003ePerform a system diagnostic check after power-up to confirm the module is recognized by the control software and that all communication registers are active.\u003c\/li\u003e\n\u003c\/ol\u003e","brand":"GE FANUC","offers":[{"title":"Default Title","offer_id":52462700822840,"sku":"IS200BICLH1AED","price":220.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0893\/1616\/3896\/files\/IS200BICLH1AED.jpg?v=1780472877","url":"https:\/\/www.automodulexpert.com\/products\/is200biclh1aed-general-electric-bridge-interface-card-new-stock","provider":"AutoModuleXpert Ltd.","version":"1.0","type":"link"}