{"product_id":"is200ectbg1abb-general-electric-circuit-board-new-original-stock","title":"IS200ECTBG1ABB General Electric Circuit Board New \u0026 Original Stock","description":"\u003cp\u003eThe \u003cstrong\u003eGeneral Electric IS200ECTBG1ABB\u003c\/strong\u003e, also cataloged as the \u003cstrong\u003eIS200ECTBG1\u003c\/strong\u003e Circuit Board, operates as a dedicated hardware component for signal processing and I\/O communication within Mark VI turbine control platforms.\u003c\/p\u003e\n\u003ch3\u003eHardware Specifications\u003c\/h3\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003e\u003cstrong\u003eParameter\u003c\/strong\u003e\u003c\/th\u003e\n\u003cth\u003e\u003cstrong\u003eSpecification\u003c\/strong\u003e\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eModel\u003c\/td\u003e\n\u003ctd\u003eIS200ECTBG1ABB\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBrand\u003c\/td\u003e\n\u003ctd\u003eGeneral Electric\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOrigin\u003c\/td\u003e\n\u003ctd\u003eUSA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWeight\u003c\/td\u003e\n\u003ctd\u003e1.12 kg\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDimensions\u003c\/td\u003e\n\u003ctd\u003e33.1 cm x 18 cm x 5.2 cm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOperating Temp\u003c\/td\u003e\n\u003ctd\u003e0 to 60 deg C\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePower Consumption\u003c\/td\u003e\n\u003ctd\u003e15 W (Typical)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eMounting Type\u003c\/td\u003e\n\u003ctd\u003eVME Rack Bus\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eInterface\u003c\/td\u003e\n\u003ctd\u003eMark VI I\/O Terminal Board\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003ch3\u003eProfinet \/ EtherNet\/IP Deterministic Networks\u003c\/h3\u003e\n\u003cp\u003eThe IS200ECTBG1ABB facilitates deterministic data exchange between the terminal board and the controller rack. Communication latency is managed via high-speed backplane bus protocols to ensure time-critical signal synchronization. The board supports consistent frame transmission rates required for turbine regulation, minimizing packet jitter across the control loop. Firm-ware flash compatibility allows for field updates to align with specific controller revision requirements during system maintenance or hardware lifecycle management.\u003c\/p\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cp\u003eQ: Does the IS200ECTBG1ABB support hot-swapping within the Mark VI rack?\u003c\/p\u003e\n\u003cp\u003eA: No. Power must be removed from the specific rack segment before removing or inserting the board to prevent electrical transient damage to the VME backplane pins.\u003c\/p\u003e\n\u003cp\u003eQ: What are the primary indicators for hardware health on this module?\u003c\/p\u003e\n\u003cp\u003eA: The board utilizes integrated diagnostic LEDs to monitor backplane communication status and power supply rails. A solid state indicator confirms proper bus synchronization, while flashing sequences denote specific communication fault codes defined in the Mark VI maintenance manual.\u003c\/p\u003e\n\u003ch3\u003eField Installation Guidelines\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003eVerify that the rack power supply is switched to the OFF position prior to installation.\u003c\/li\u003e\n\u003cli\u003eAlign the board with the corresponding VME slot guides. Ensure the board is oriented correctly to avoid pin misalignment on the backplane connector.\u003c\/li\u003e\n\u003cli\u003eApply firm, even pressure to the faceplate levers to seat the edge connector fully into the backplane bus.\u003c\/li\u003e\n\u003cli\u003eSecure the module using the integrated captive screws on the faceplate to ensure electrical grounding between the chassis and the board shielding.\u003c\/li\u003e\n\u003cli\u003eInspect the terminal wiring for tension. Cables must be routed through the designated cable ducts to prevent mechanical stress on the board connectors during thermal expansion.\u003c\/li\u003e\n\u003cli\u003eShielded cables must be grounded at the designated chassis termination points to reduce electromagnetic interference (EMI) impact on analog signal loops.\u003c\/li\u003e\n\u003c\/ol\u003e","brand":"GE FANUC","offers":[{"title":"Default Title","offer_id":52462592786744,"sku":"IS200ECTBG1ABB","price":220.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0893\/1616\/3896\/files\/IS200ECTBG1ABB.jpg?v=1780472877","url":"https:\/\/www.automodulexpert.com\/products\/is200ectbg1abb-general-electric-circuit-board-new-original-stock","provider":"AutoModuleXpert Ltd.","version":"1.0","type":"link"}