{"product_id":"is200egpag1bec-general-electric-exciter-gate-pulse-amplifier-board","title":"IS200EGPAG1BEC General Electric Exciter Gate Pulse Amplifier Board","description":"\u003cp\u003eConfigured for signal amplification and gate control in excitation systems, the \u003cstrong\u003eGeneral Electric IS200EGPAG1BEC\u003c\/strong\u003e (\u003cstrong\u003eIS200EGPAG1BEC\u003c\/strong\u003e Exciter Gate Pulse Amplifier Board) provides direct physical\/electrical execution. This module generates and conditions the gate drive signals required to trigger power semiconductor devices within the exciter bridge, maintaining precise control over field current modulation.\u003c\/p\u003e\n\u003ch3\u003eSuffix Breakdown \u0026amp; Model Matrix\u003c\/h3\u003e\n\u003cp\u003eThe IS200EGPAG1BEC is a specific revision of the EGPA hardware platform. The \"G1\" designation refers to the functional board assembly version, while the trailing \"BEC\" indicates the specific firmware\/hardware iteration and manufacturing release level. This module is not field-configurable for alternative gate pulse logic and must be replaced with an identical suffix code to ensure compatibility with existing bridge hardware.\u003c\/p\u003e\n\u003ch3\u003eHardware Specifications\u003c\/h3\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003e\u003cstrong\u003eParameter\u003c\/strong\u003e\u003c\/th\u003e\n\u003cth\u003e\u003cstrong\u003eSpecification\u003c\/strong\u003e\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eModel\u003c\/td\u003e\n\u003ctd\u003eIS200EGPAG1BEC\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBrand\u003c\/td\u003e\n\u003ctd\u003eGeneral Electric\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOrigin\u003c\/td\u003e\n\u003ctd\u003eUSA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWeight\u003c\/td\u003e\n\u003ctd\u003e0.8 kg\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDimensions\u003c\/td\u003e\n\u003ctd\u003e14.75 cm x 9.50 cm x 3.50 cm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOperating Temp\u003c\/td\u003e\n\u003ctd\u003e-20 deg C to +60 deg C\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePower Consumption\u003c\/td\u003e\n\u003ctd\u003e\u0026lt; 15 W\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSignal Output\u003c\/td\u003e\n\u003ctd\u003eGate pulse amplification for SCR bridge\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003ch3\u003eProfinet \/ EtherNet\/IP Deterministic Networks\u003c\/h3\u003e\n\u003cp\u003eWhile the IS200EGPAG1BEC functions primarily as an analog pulse amplifier, it integrates into the broader control network through the excitation controller's communication interface. The board ensures that gate pulse timing remains synchronous with the deterministic network cycle, preventing jitter that could lead to power device commutation failure. Firmware flash compatibility allows the controller to update the pulse firing sequence parameters, ensuring that the module maintains alignment with the current system firing angle requirements and network-derived synchronization pulses.\u003c\/p\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cp\u003eQ: Can the IS200EGPAG1BEC be hot-swapped while the bridge is in a standby state?\u003c\/p\u003e\n\u003cp\u003eA: No. Hot-swapping is prohibited. The exciter bridge must be completely de-energized, and the DC bus must be verified as discharged to a safe voltage level before the board is removed or installed to protect the sensitive gate drive circuitry.\u003c\/p\u003e\n\u003cp\u003eQ: How should the gate pulse feedback signals be verified after installation?\u003c\/p\u003e\n\u003cp\u003eA: Verification must be performed using an oscilloscope to monitor the pulse amplitude and pulse width at the test points designated in the system wiring diagrams, ensuring they meet the required gate turn-on thresholds for the specific semiconductor devices installed in the bridge.\u003c\/p\u003e\n\u003ch3\u003eField Installation Guidelines\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003eVerify that all AC and DC supply power to the exciter bridge is disconnected and locked out.\u003c\/li\u003e\n\u003cli\u003eEnsure the technician is equipped with a grounded electrostatic discharge (ESD) wrist strap to prevent damage to the board circuitry during handling.\u003c\/li\u003e\n\u003cli\u003eAlign the board with the mounting standoffs, ensuring that all gate pulse cable connectors are properly seated and keyed according to the interface labels.\u003c\/li\u003e\n\u003cli\u003eVerify that cable shields are grounded at the control cabinet entry point to minimize noise injection into the gate drive lines.\u003c\/li\u003e\n\u003cli\u003eInspect the pulse transformer connections for mechanical stability and ensure no loose wiring exists that could cause intermittent contact during bridge operation.\u003c\/li\u003e\n\u003c\/ol\u003e","brand":"GE FANUC","offers":[{"title":"Default Title","offer_id":52555171037496,"sku":"IS200EGPAG1BEC","price":220.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0893\/1616\/3896\/files\/IS200EGPAG1BEC2.jpg?v=1782287375","url":"https:\/\/www.automodulexpert.com\/products\/is200egpag1bec-general-electric-exciter-gate-pulse-amplifier-board","provider":"AutoModuleXpert Ltd.","version":"1.0","type":"link"}