{"product_id":"is200eroch1abc-general-electric-i-o-module-new-original-stock","title":"IS200EROCH1ABC General Electric I\/O Module | New \u0026 Original Stock","description":"\u003cp\u003eThe \u003cstrong\u003eGeneral Electric IS200EROCH1ABC\u003c\/strong\u003e, also cataloged as the \u003cstrong\u003eIS200EROCH1ABC\u003c\/strong\u003e I\/O Module, operates as a dedicated hardware component for relay control and signal routing within Mark VI and EX2100 control system architectures.\u003c\/p\u003e\n\u003ch3\u003eHardware Specifications\u003c\/h3\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003e\u003cstrong\u003eParameter\u003c\/strong\u003e\u003c\/th\u003e\n\u003cth\u003e\u003cstrong\u003eSpecification\u003c\/strong\u003e\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eModel\u003c\/td\u003e\n\u003ctd\u003eIS200EROCH1ABC\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBrand\u003c\/td\u003e\n\u003ctd\u003eGeneral Electric\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOrigin\u003c\/td\u003e\n\u003ctd\u003eUSA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWeight\u003c\/td\u003e\n\u003ctd\u003e0.8 kg\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOperating Temp\u003c\/td\u003e\n\u003ctd\u003e-20 to 60 deg C\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eInput Voltage\u003c\/td\u003e\n\u003ctd\u003e24 VDC (± 10%)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePower Consumption\u003c\/td\u003e\n\u003ctd\u003e15 W\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003ch3\u003eProfinet \/ EtherNet\/IP Deterministic Networks\u003c\/h3\u003e\n\u003cp\u003eThe IS200EROCH1ABC functions as a high-density I\/O regulator interface, utilizing deterministic bus communication to synchronize relay output states with the control processor. It facilitates I\/O density scaling by providing structured paths for digital control commands, ensuring that signal execution remains within strict timing windows required for excitation and turbine control. The module architecture incorporates signal buffering and firmware flash compatibility, allowing it to adapt to evolving network protocols and control logic requirements while maintaining signal integrity across the backplane communication velocity paths.\u003c\/p\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cp\u003eQ: Is the IS200EROCH1ABC hot-swappable in an active control rack?\u003c\/p\u003e\n\u003cp\u003eA: No, this module does not support hot-swapping. The control rack must be de-energized, and all supply voltages verified at 0 VDC before performing installation or removal to prevent damage to the backplane edge connectors.\u003c\/p\u003e\n\u003cp\u003eQ: How can I verify the module is correctly receiving network communication?\u003c\/p\u003e\n\u003cp\u003eA: Monitor the diagnostic LEDs on the module front panel. A steady operational state confirms successful synchronization with the rack master processor, while blinking or red states indicate a communication timeout or firmware synchronization failure.\u003c\/p\u003e\n\u003ch3\u003eField Installation Guidelines\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003ePower down the I\/O rack and isolate all 24 VDC input sources to ensure a safe working environment.\u003c\/li\u003e\n\u003cli\u003eUtilize ESD-safe practices; ensure you are grounded to the cabinet chassis before opening the anti-static packaging or handling the board.\u003c\/li\u003e\n\u003cli\u003eAlign the module with the rack guide rails, ensuring the backplane connector pin array is clear of debris.\u003c\/li\u003e\n\u003cli\u003eSeat the board firmly into the backplane, and tighten the front-panel captive screws to secure the module and establish a consistent chassis ground connection.\u003c\/li\u003e\n\u003cli\u003eVerify that all field wiring connected to the terminal blocks is properly torqued and that shield drain wires are terminated only at the designated common ground point to prevent electromagnetic interference.\u003c\/li\u003e\n\u003c\/ol\u003e","brand":"GE FANUC","offers":[{"title":"Default Title","offer_id":52469592326456,"sku":"IS200EROCH1ABC","price":220.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0893\/1616\/3896\/files\/IS200ERDDH1ABB2.jpg?v=1780560041","url":"https:\/\/www.automodulexpert.com\/products\/is200eroch1abc-general-electric-i-o-module-new-original-stock","provider":"AutoModuleXpert Ltd.","version":"1.0","type":"link"}