{"product_id":"is200erscg2a-general-electric-exciter-regulator-datasheet","title":"IS200ERSCG2A General Electric Exciter Regulator | Datasheet","description":"\u003cp\u003eConfigured for pulse-width modulation exciter regulation in EX2100 control systems, the \u003cstrong\u003eGeneral Electric IS200ERSCG2A\u003c\/strong\u003e (\u003cstrong\u003eIS200ERSG2A\u003c\/strong\u003e Exciter Regulator) provides direct electrical execution for field discharge and DC-link power management.\u003c\/p\u003e\n\u003ch3\u003eHardware Specifications\u003c\/h3\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003e\u003cstrong\u003eParameter\u003c\/strong\u003e\u003c\/th\u003e\n\u003cth\u003e\u003cstrong\u003eSpecification\u003c\/strong\u003e\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eModel\u003c\/td\u003e\n\u003ctd\u003eIS200ERSCG2A\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBrand\u003c\/td\u003e\n\u003ctd\u003eGeneral Electric\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOrigin\u003c\/td\u003e\n\u003ctd\u003eUSA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWeight\u003c\/td\u003e\n\u003ctd\u003e0.3kg\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDimensions\u003c\/td\u003e\n\u003ctd\u003eNot specified\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOperating Temp\u003c\/td\u003e\n\u003ctd\u003eStandard industrial ambient range\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePower Consumption\u003c\/td\u003e\n\u003ctd\u003eNot specified\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSwitching Components\u003c\/td\u003e\n\u003ctd\u003e6 x IGBTs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eCommunication\u003c\/td\u003e\n\u003ctd\u003eSerial \/ Ethernet Modbus\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOperating Modes\u003c\/td\u003e\n\u003ctd\u003eSimplex \/ Redundant\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003ch3\u003ePLC and Control Deterministic Networks\u003c\/h3\u003e\n\u003cp\u003eThe IS200ERSCG2A integrates into the EX2100 architecture via deterministic communication channels, requiring precise synchronization with the host controller to maintain loop stability. The module supports firmware flash compatibility, allowing for updates to the internal logic governing PWM timing and protection thresholds. To ensure reliable performance, the backplane bus communication velocity must be configured to match the polling rate of the master controller. Engineers should verify that the firmware revision on the IS200ERSCG2A is compatible with the existing ERDD, ERRR, ERBP, ERRB, and ERIO board revisions within the same rack.\u003c\/p\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cp\u003eQ: Is this controller capable of operating in a TMR configuration?\u003c\/p\u003e\n\u003cp\u003eA: Yes, the IS200ERSCG2A supports both simplex and redundant operating modes. When integrated into a redundant system, proper synchronization of the pulse-width modulation signals across all active modules is required to prevent differential current flow in the exciter field.\u003c\/p\u003e\n\u003cp\u003eQ: Can the internal relays be replaced if they fail?\u003c\/p\u003e\n\u003cp\u003eA: No. The IS200ERSCG2A is a sealed hardware component. In the event of a relay or IGBT failure, the entire module must be replaced to ensure system integrity and compliance with safety standards.\u003c\/p\u003e\n\u003ch3\u003eField Installation Guidelines\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003eEnsure the control system is fully de-energized before mounting the module in the EX2100 rack.\u003c\/li\u003e\n\u003cli\u003eConfirm the module is firmly seated in the slot to establish solid contact with the backplane connectors.\u003c\/li\u003e\n\u003cli\u003eTighten the front-panel retaining screws to maintain mechanical stability and proper grounding connection to the chassis.\u003c\/li\u003e\n\u003cli\u003eVerify the integrity of the communication cables (Serial or Ethernet Modbus) before restoring power to the exciter cabinet.\u003c\/li\u003e\n\u003cli\u003ePerform a check of the DC-link charging resistor bypass circuitry to ensure no pre-charge faults exist before initiating field excitation.\u003c\/li\u003e\n\u003c\/ol\u003e","brand":"GE FANUC","offers":[{"title":"Default Title","offer_id":52473319358776,"sku":"IS200ERSCG2A","price":220.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0893\/1616\/3896\/files\/IS215VCMIH2B.jpg?v=1780646919","url":"https:\/\/www.automodulexpert.com\/products\/is200erscg2a-general-electric-exciter-regulator-datasheet","provider":"AutoModuleXpert Ltd.","version":"1.0","type":"link"}