{"product_id":"is200esysh3a-ge-interface-board-new-original-stock","title":"IS200ESYSH3A GE Interface Board | New \u0026 Original Stock","description":"\u003cp\u003eThe \u003cstrong\u003eGE IS200ESYSH3A\u003c\/strong\u003e, also cataloged as the \u003cstrong\u003eIS200ESYS\u003c\/strong\u003e Interface Board, operates as a dedicated hardware component for high-speed serial link communication within EX2100E control system platforms.\u003c\/p\u003e\n\u003ch3\u003eHardware Specifications\u003c\/h3\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003e\u003cstrong\u003eParameter\u003c\/strong\u003e\u003c\/th\u003e\n\u003cth\u003e\u003cstrong\u003eSpecification\u003c\/strong\u003e\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eModel\u003c\/td\u003e\n\u003ctd\u003eIS200ESYSH3A\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBrand\u003c\/td\u003e\n\u003ctd\u003eGE\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOrigin\u003c\/td\u003e\n\u003ctd\u003eUSA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWeight\u003c\/td\u003e\n\u003ctd\u003e0.45 kg\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDimensions\u003c\/td\u003e\n\u003ctd\u003eStandard EX2100E form factor\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOperating Temp\u003c\/td\u003e\n\u003ctd\u003eStandard Industrial\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePower Consumption\u003c\/td\u003e\n\u003ctd\u003eSystem bus nominal\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eCore Function\u003c\/td\u003e\n\u003ctd\u003eHigh-speed serial communication\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003ch3\u003eFirmware and Backplane Communication\u003c\/h3\u003e\n\u003cp\u003eThe IS200ESYSH3A facilitates deterministic data exchange by managing the high-speed serial link between the EX2100E controller and auxiliary drive interface modules. The module utilizes backplane bus communication velocity settings optimized for low-latency feedback transmission. Firmware flash compatibility is strictly managed through the EX2100E control suite, requiring users to verify hardware revisions against the current system firmware version to ensure successful handshaking. I\/O density scaling is maintained by the board's ability to aggregate multi-channel serial data into a unified stream for the primary processor.\u003c\/p\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cp\u003eQ: Is the IS200ESYSH3A module backwards compatible with previous versions of the EX2100 system?\u003c\/p\u003e\n\u003cp\u003eA: Compatibility is dependent on the specific firmware version and backplane revision. Consult the EX2100E system manual for the specific hardware\/firmware matrix requirements before attempting to install this module as a replacement for older interface boards.\u003c\/p\u003e\n\u003cp\u003eQ: What are the primary indicators of a communication failure on this board?\u003c\/p\u003e\n\u003cp\u003eA: Diagnostic LEDs on the module indicate link status and internal fault conditions. A loss of communication or a \"Bus Error\" message in the controller diagnostic software typically indicates either a physical failure of the serial link cable or an internal synchronization fault within the interface board.\u003c\/p\u003e\n\u003ch3\u003eField Installation Guidelines\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eVerify that all high-speed serial cabling is properly shielded and grounded to prevent electromagnetic interference from the drive's power section.\u003c\/li\u003e\n\u003cli\u003eEnsure the module is fully seated in the designated backplane slot to prevent intermittent data loss caused by poor pin contact.\u003c\/li\u003e\n\u003cli\u003eBefore initialization, verify that the module's physical address settings or configuration jumpers match the requirements of the EX2100E cabinet map.\u003c\/li\u003e\n\u003cli\u003eConfirm that the board is protected against electrostatic discharge (ESD) during handling to prevent damage to the high-density serial transceiver components.\u003c\/li\u003e\n\u003cli\u003eOnce installed, perform a system diagnostic scan to verify that the high-speed serial link is established and that no frame errors are being reported by the host controller.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"GE FANUC","offers":[{"title":"Default Title","offer_id":52514985115960,"sku":"IS200ESYSH3A","price":220.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0893\/1616\/3896\/files\/IS200ESYSH3A.jpg?v=1781596213","url":"https:\/\/www.automodulexpert.com\/products\/is200esysh3a-ge-interface-board-new-original-stock","provider":"AutoModuleXpert Ltd.","version":"1.0","type":"link"}