{"product_id":"is200hslah2a-ge-serial-link-interface-boards-datasheet-technical-manual","title":"IS200HSLAH2A GE Serial Link Interface Boards Datasheet \u0026 Technical Manual","description":"\u003cp\u003eThe \u003cstrong\u003eGE IS200HSLAH2A\u003c\/strong\u003e, also cataloged as the \u003cstrong\u003eIS200HSLA\u003c\/strong\u003e Serial Link Interface Board, operates as a dedicated hardware component for serial data communication and protocol management within Mark VI control system platforms.\u003c\/p\u003e\n\u003ch3\u003eHardware Specifications\u003c\/h3\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003e\u003cstrong\u003eParameter\u003c\/strong\u003e\u003c\/th\u003e\n\u003cth\u003e\u003cstrong\u003eSpecification\u003c\/strong\u003e\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eModel\u003c\/td\u003e\n\u003ctd\u003eIS200HSLAH2A\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBrand\u003c\/td\u003e\n\u003ctd\u003eGeneral Electric\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOrigin\u003c\/td\u003e\n\u003ctd\u003eUSA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWeight\u003c\/td\u003e\n\u003ctd\u003e0.5 kg\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDimensions\u003c\/td\u003e\n\u003ctd\u003e200 mm x 100 mm x 40 mm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOperating Temp\u003c\/td\u003e\n\u003ctd\u003eStandard industrial ambient range\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePower Consumption\u003c\/td\u003e\n\u003ctd\u003eDetermined by backplane rail loading\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eInterface Type\u003c\/td\u003e\n\u003ctd\u003eSerial Link\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003ch3\u003eProfinet \/ EtherNet\/IP Deterministic Networks\u003c\/h3\u003e\n\u003cp\u003eThe IS200HSLAH2A is designed to facilitate deterministic data exchange between distributed control units and central processing modules. This module handles the serialization of control signals, ensuring that high-speed network traffic remains synchronized with the processor scan cycle. Firmware flash compatibility is strictly governed by the host controller's I\/O configuration, requiring exact revision matching to ensure backplane bus communication velocity remains within defined operational limits. Improper configuration of the serial baud rate or link parameters will result in protocol framing errors during high-load network conditions.\u003c\/p\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cp\u003eQ: Is this board compatible with live-insertion (hot-swap) procedures in the control rack?\u003c\/p\u003e\n\u003cp\u003eA: No. The backplane bus must be de-energized before mounting or dismounting the IS200HSLAH2A to prevent transient surges from damaging the communication interface integrated circuits.\u003c\/p\u003e\n\u003cp\u003eQ: How is the serial communication link shielded against industrial electromagnetic interference (EMI)?\u003c\/p\u003e\n\u003cp\u003eA: The board relies on the rack's chassis ground and properly terminated shielded twisted-pair cabling. Users must ensure the shield drain wire is connected to the designated ground terminal on the rack backplane to minimize signal distortion.\u003c\/p\u003e\n\u003ch3\u003eField Installation Guidelines\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eVerify that the rack power supply is isolated and the system is in a controlled state before installation.\u003c\/li\u003e\n\u003cli\u003eEnsure the module is seated correctly in the designated VME slot, confirming that all guide pins are fully engaged before tightening faceplate screws.\u003c\/li\u003e\n\u003cli\u003eMaintain a minimum clearance of 50 mm around the module's perimeter to allow for passive heat dissipation from internal surface components.\u003c\/li\u003e\n\u003cli\u003eRoute all serial communication cables through designated cable trays, maintaining physical separation from power cabling to mitigate crosstalk and induced noise.\u003c\/li\u003e\n\u003cli\u003eUse appropriate electrostatic discharge (ESD) mitigation protocols, including the use of a wrist strap, during the entire handling and installation process to protect sensitive onboard logic.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"GE FANUC","offers":[{"title":"Default Title","offer_id":52493476921656,"sku":"IS200HSLAH2A","price":220.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0893\/1616\/3896\/files\/IS200HSLAH2A2.jpg?v=1781165690","url":"https:\/\/www.automodulexpert.com\/products\/is200hslah2a-ge-serial-link-interface-boards-datasheet-technical-manual","provider":"AutoModuleXpert Ltd.","version":"1.0","type":"link"}