{"product_id":"is200isbeh2a-general-electric-printed-circuit-board-new-original-stock","title":"IS200ISBEH2A General Electric Printed Circuit Board | New \u0026 Original Stock","description":"\u003cp\u003eThe \u003cstrong\u003eGeneral Electric IS200ISBEH2A\u003c\/strong\u003e, also cataloged as the \u003cstrong\u003eIS200ISBEH2A\u003c\/strong\u003e Printed Circuit Board, operates as a dedicated hardware component for signal processing and bridge interface management within Speedtronic Mark VI control systems.\u003c\/p\u003e\n\u003ch3\u003eHardware Specifications\u003c\/h3\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003e\u003cstrong\u003eParameter\u003c\/strong\u003e\u003c\/th\u003e\n\u003cth\u003e\u003cstrong\u003eSpecification\u003c\/strong\u003e\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eModel\u003c\/td\u003e\n\u003ctd\u003eIS200ISBEH2A\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBrand\u003c\/td\u003e\n\u003ctd\u003eGeneral Electric\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOrigin\u003c\/td\u003e\n\u003ctd\u003eUSA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWeight\u003c\/td\u003e\n\u003ctd\u003e0.3 kg\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDimensions\u003c\/td\u003e\n\u003ctd\u003e9.2 cm x 5.0 cm x 11.0 cm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOperating Temp\u003c\/td\u003e\n\u003ctd\u003e-20 deg C to 60 deg C\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePower Consumption\u003c\/td\u003e\n\u003ctd\u003e\u0026lt; 5 W\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDevice Function\u003c\/td\u003e\n\u003ctd\u003eBridge Interface Printed Circuit Board\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003ch3\u003eProfinet \/ EtherNet\/IP Deterministic Networks\u003c\/h3\u003e\n\u003cp\u003eThe IS200ISBEH2A serves as an integral node within the GE control architecture, facilitating data exchange across high-speed deterministic networks. It is engineered to maintain signal integrity during high-frequency backplane bus communication. The module utilizes standardized gate array logic to manage I\/O data throughput, ensuring that cyclic communication timings remain within defined millisecond tolerances. Firmware flash compatibility is managed via the primary controller rack, requiring specific hardware revision parity to ensure deterministic execution of control algorithms without latency jitter.\u003c\/p\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cp\u003eQ: Does the IS200ISBEH2A board support field-level hot-swapping while the rack is powered?\u003c\/p\u003e\n\u003cp\u003eA: No. Standard GE Mark VI hardware protocols require the corresponding control rack slot to be de-energized prior to board extraction or insertion to prevent backplane circuit damage or electrostatic discharge (ESD) events.\u003c\/p\u003e\n\u003cp\u003eQ: What are the primary diagnostic indicators to monitor for this board?\u003c\/p\u003e\n\u003cp\u003eA: The board relies on the main controller rack diagnostic software. Monitor the health status bits via the WorkstationST interface; loss of communication or bridge interface timeouts are typically flagged as specific fault codes in the system log.\u003c\/p\u003e\n\u003ch3\u003eField Installation Guidelines\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eElectrostatic Discharge: Always utilize a grounded wrist strap when handling the IS200ISBEH2A to prevent damage to sensitive CMOS components on the PCB.\u003c\/li\u003e\n\u003cli\u003eMounting Stability: Ensure the board is fully seated within the designated VME-style backplane connector. Verify that the top and bottom locking levers are secured in the closed position to maintain mechanical alignment.\u003c\/li\u003e\n\u003cli\u003eShielding and Grounding: Ensure that the I\/O cabling connected to the bridge interface is properly shielded. Cable shields must be terminated at the designated ground bus bar within the cabinet to minimize electromagnetic interference (EMI) ingress.\u003c\/li\u003e\n\u003cli\u003eCabling Constraints: Do not exceed the physical bend radius of connected ribbon or signal cables. Ensure cables are routed through designated wire ways to prevent mechanical stress on the board-to-cable interface connectors.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"GE FANUC","offers":[{"title":"Default Title","offer_id":52496004153656,"sku":"IS200ISBEH2A","price":220.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0893\/1616\/3896\/files\/IS200ISBEH1ABB1_e790b78c-3a2b-4488-ad00-0fdb533f5550.jpg?v=1763449150","url":"https:\/\/www.automodulexpert.com\/products\/is200isbeh2a-general-electric-printed-circuit-board-new-original-stock","provider":"AutoModuleXpert Ltd.","version":"1.0","type":"link"}