{"product_id":"is200srlyh2a-general-electric-discrete-output-module-new-original-stock","title":"IS200SRLYH2A General Electric Discrete Output Module | New \u0026 Original Stock","description":"\u003cp\u003eConfigured for discrete output switching in Speedtronic Mark VI control systems, the \u003cstrong\u003eGeneral Electric IS200SRLYH2A\u003c\/strong\u003e (\u003cstrong\u003eIS200SRLYH2A\u003c\/strong\u003e Discrete Output Module) provides direct physical\/electrical execution for relay contact interface management.\u003c\/p\u003e\n\u003ch3\u003eHardware Specifications\u003c\/h3\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003e\u003cstrong\u003eParameter\u003c\/strong\u003e\u003c\/th\u003e\n\u003cth\u003e\u003cstrong\u003eSpecification\u003c\/strong\u003e\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eModel\u003c\/td\u003e\n\u003ctd\u003eIS200SRLYH2A\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBrand\u003c\/td\u003e\n\u003ctd\u003eGeneral Electric\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOrigin\u003c\/td\u003e\n\u003ctd\u003eUSA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWeight\u003c\/td\u003e\n\u003ctd\u003e1.14 kg\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDimensions\u003c\/td\u003e\n\u003ctd\u003e22.5 cm x 16.7 cm x 5.5 cm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOperating Temp\u003c\/td\u003e\n\u003ctd\u003e0 to 60 deg C\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePower Consumption\u003c\/td\u003e\n\u003ctd\u003eSubject to load configuration\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOutput Type\u003c\/td\u003e\n\u003ctd\u003eDiscrete Relay Contact\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eInterface Protocol\u003c\/td\u003e\n\u003ctd\u003eMark VI Backplane Bus\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003ch3\u003eBackplane Bus Communication Velocity\u003c\/h3\u003e\n\u003cp\u003eThe IS200SRLYH2A module interfaces with the Mark VI controller backplane to maintain deterministic discrete signal transmission. Data transfer rates are governed by the specific backplane bus communication velocity settings, ensuring that relay status updates are synchronized with the control processor scan cycle. Firmware compatibility must be verified against the Mark VI main processor rack revision to ensure proper bit-field alignment during module initialization.\u003c\/p\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cp\u003eQ: Does the IS200SRLYH2A support field-side hot-swapping?\u003c\/p\u003e\n\u003cp\u003eA: No. Power must be removed from the terminal board and the I\/O rack prior to module extraction to prevent transient voltage spikes and potential damage to the backplane connectors.\u003c\/p\u003e\n\u003cp\u003eQ: What are the primary concerns regarding relay contact wear?\u003c\/p\u003e\n\u003cp\u003eA: The relays are rated for a specific number of mechanical and electrical cycles. Inductive loads must be suppressed using external flyback diodes or RC snubber circuits to prevent contact pitting and welding during de-energization.\u003c\/p\u003e\n\u003ch3\u003eField Installation Guidelines\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eEnsure the module is seated fully into the designated VME slot; secure the top and bottom captive screws to establish a chassis ground connection.\u003c\/li\u003e\n\u003cli\u003eVerify that the wiring on the associated terminal board matches the I\/O terminal assignment diagram for the IS200SRLYH2A to prevent incorrect circuit energization.\u003c\/li\u003e\n\u003cli\u003eShielded cabling must be used for all I\/O wiring; the shield drain wire should be landed on the designated chassis ground stud on the cabinet backplane.\u003c\/li\u003e\n\u003cli\u003eMaintain a minimum clearance of 5 cm above and below the module to facilitate adequate convective airflow within the control cabinet.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"GE FANUC","offers":[{"title":"Default Title","offer_id":52487702544696,"sku":"IS200SRLYH2A","price":220.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0893\/1616\/3896\/files\/IS200SRLYH2A.jpg?v=1781078008","url":"https:\/\/www.automodulexpert.com\/products\/is200srlyh2a-general-electric-discrete-output-module-new-original-stock","provider":"AutoModuleXpert Ltd.","version":"1.0","type":"link"}