{"product_id":"is200sscah2a-ge-communication-i-o-terminal-board-datasheet","title":"IS200SSCAH2A GE Communication I\/O Terminal Board | Datasheet","description":"\u003cp\u003eThe \u003cstrong\u003eGE IS200SSCAH2A\u003c\/strong\u003e, also cataloged as the \u003cstrong\u003eIS200SSCAH2\u003c\/strong\u003e Communication I\/O Terminal Board, operates as a dedicated hardware component for serial data signal routing and interface management within Mark VI control system networks.\u003c\/p\u003e\n\u003ch3\u003eHardware Specifications\u003c\/h3\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003e\u003cstrong\u003eParameter\u003c\/strong\u003e\u003c\/th\u003e\n\u003cth\u003e\u003cstrong\u003eSpecification\u003c\/strong\u003e\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eModel\u003c\/td\u003e\n\u003ctd\u003eIS200SSCAH2A\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBrand\u003c\/td\u003e\n\u003ctd\u003eGE\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOrigin\u003c\/td\u003e\n\u003ctd\u003eUSA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWeight\u003c\/td\u003e\n\u003ctd\u003e0.3 kg\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDimensions\u003c\/td\u003e\n\u003ctd\u003e3.5 cm x 13 cm x 13.5 cm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOperating Temp\u003c\/td\u003e\n\u003ctd\u003e0 to 60 deg C\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePower Consumption\u003c\/td\u003e\n\u003ctd\u003e24 VDC\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eCommunication Ports\u003c\/td\u003e\n\u003ctd\u003eRS-232 \/ RS-485\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003ch3\u003eControl System Connectivity and Bus Communication\u003c\/h3\u003e\n\u003cp\u003eThe IS200SSCAH2A board serves as a physical layer interface to facilitate backplane bus communication. It manages the electrical signal conversion required for serial data exchange between external devices and the I\/O processor. The module architecture is designed to support specific backplane bus communication velocity settings defined in the controller configuration, ensuring that data packets are processed without timing errors. Integration requires that the board firmware flash compatibility is verified against the main processor version to ensure proper handshaking and protocol handling within the deterministic network environment.\u003c\/p\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cp\u003eQ: Can this terminal board be replaced while the control rack is energized?\u003c\/p\u003e\n\u003cp\u003eA: No. The IS200SSCAH2A does not support hot-swapping. You must isolate all field power and rack power before attempting to extract or install the board to prevent electrical short-circuits or damage to the backplane communication pins.\u003c\/p\u003e\n\u003cp\u003eQ: How should communication cables be shielded when connected to this board?\u003c\/p\u003e\n\u003cp\u003eA: Communication shields should be terminated to the designated high-frequency chassis ground studs provided on the cabinet entry point, rather than directly to the board's signal reference, to maintain effective noise immunity and prevent ground loops.\u003c\/p\u003e\n\u003ch3\u003eField Installation Guidelines\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eMounting:\u003c\/strong\u003e Inspect the I\/O rack slot for debris before seating the IS200SSCAH2A. Ensure the board slides along the guide rails until the edge connector is fully seated into the backplane receptacle.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSignal Integrity:\u003c\/strong\u003e Route serial data cables away from high-voltage AC lines or inductive load wiring to minimize electromagnetic interference. Maintain a minimum separation of 15 cm for parallel runs.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTermination:\u003c\/strong\u003e Verify that RS-485 termination resistors are installed at the physical ends of the communication bus if required by the specific application topology.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eVerification:\u003c\/strong\u003e After installation, confirm that the module status LED indicates a healthy state. Utilize the control system diagnostic software to verify clear communication packets and the absence of frame errors on the port.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"GE FANUC","offers":[{"title":"Default Title","offer_id":52495915548984,"sku":"IS200SSCAH2A","price":220.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0893\/1616\/3896\/files\/IS200SSCAH2AGD1.jpg?v=1760171733","url":"https:\/\/www.automodulexpert.com\/products\/is200sscah2a-ge-communication-i-o-terminal-board-datasheet","provider":"AutoModuleXpert Ltd.","version":"1.0","type":"link"}