{"product_id":"is200tbaih1c-ge-analog-input-terminal-board-new-original-stock","title":"IS200TBAIH1C GE Analog Input Terminal Board | New \u0026 Original Stock","description":"\u003cp\u003eConfigured for analog signal termination in Mark VI control systems, the \u003cstrong\u003eGE IS200TBAIH1C\u003c\/strong\u003e (\u003cstrong\u003eIS200TBAIH1C\u003c\/strong\u003e Terminal Board) provides direct physical and electrical execution for sensor-to-processor interface.\u003c\/p\u003e\n\u003ch3\u003eHardware Specifications\u003c\/h3\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003e\u003cstrong\u003eParameter\u003c\/strong\u003e\u003c\/th\u003e\n\u003cth\u003e\u003cstrong\u003eSpecification\u003c\/strong\u003e\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eModel\u003c\/td\u003e\n\u003ctd\u003eIS200TBAIH1C\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBrand\u003c\/td\u003e\n\u003ctd\u003eGE\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOrigin\u003c\/td\u003e\n\u003ctd\u003eUSA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWeight\u003c\/td\u003e\n\u003ctd\u003e1.00 lbs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDimensions\u003c\/td\u003e\n\u003ctd\u003eStandard Mark VI footprint\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOperating Temp\u003c\/td\u003e\n\u003ctd\u003e-30 to 65 deg C\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePower Consumption\u003c\/td\u003e\n\u003ctd\u003eDerived from backplane bus\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSignal Compatibility\u003c\/td\u003e\n\u003ctd\u003eAnalog Input (Current\/Voltage)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSystem Platform\u003c\/td\u003e\n\u003ctd\u003eMark VI\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003ch3\u003eProfinet \/ EtherNet\/IP Deterministic Networks\u003c\/h3\u003e\n\u003cp\u003eThe IS200TBAIH1C integrates into the Mark VI control architecture to facilitate signal distribution across deterministic networks. Effective signal integrity is maintained through optimized PCB trace layouts, ensuring minimal impedance mismatch during data acquisition. Compatibility with established controller firmware requires verification of the current board revision to ensure proper handshaking with the associated I\/O processor modules.\u003c\/p\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cp\u003eQ: Does this terminal board support hot-swapping during active system operation?\u003c\/p\u003e\n\u003cp\u003eA: No. Power must be removed from the local I\/O rack prior to the physical extraction or installation of the IS200TBAIH1C to prevent transient spikes and potential backplane bus damage.\u003c\/p\u003e\n\u003cp\u003eQ: What are the primary grounding requirements for the analog input signals?\u003c\/p\u003e\n\u003cp\u003eA: Shields must be terminated to the designated chassis ground studs on the board. Avoid creating ground loops by ensuring that signal returns are consistent with the specific loop configuration mandated by the Mark VI controller documentation.\u003c\/p\u003e\n\u003ch3\u003eField Installation Guidelines\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eEnsure all DIN-rail mounting hardware is torqued to manufacturer specifications to prevent mechanical vibration under high-load conditions.\u003c\/li\u003e\n\u003cli\u003eVerify that incoming field wiring does not exceed the maximum gauge specified for the terminal block connectors to maintain low contact resistance.\u003c\/li\u003e\n\u003cli\u003eMaintain physical segregation between signal-level wiring and high-voltage AC or DC power conduits to mitigate electromagnetic interference (EMI).\u003c\/li\u003e\n\u003cli\u003ePerform a baseline check of signal voltage levels at the terminal points prior to finalizing the software configuration to confirm proper sensor scaling and excitation loop continuity.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"GE FANUC","offers":[{"title":"Default Title","offer_id":52473359139128,"sku":"IS200TBAIH1C","price":220.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0893\/1616\/3896\/files\/IS200TBAIH1C1.jpg?v=1780646917","url":"https:\/\/www.automodulexpert.com\/products\/is200tbaih1c-ge-analog-input-terminal-board-new-original-stock","provider":"AutoModuleXpert Ltd.","version":"1.0","type":"link"}