{"product_id":"is200trlyh1bge-ge-fanuc-circuit-board-new-original-stock","title":"IS200TRLYH1BGE GE Fanuc Circuit Board | New \u0026 Original Stock","description":"\u003cp\u003eThe \u003cstrong\u003eGE Fanuc IS200TRLYH1BGE\u003c\/strong\u003e, also cataloged as the \u003cstrong\u003eIS200TRLYH1BGE\u003c\/strong\u003e Circuit Board, operates as a dedicated hardware component for relay logic distribution and output signal switching within Mark VI control system architectures.\u003c\/p\u003e\n\u003ch3\u003eHardware Specifications\u003c\/h3\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003e\u003cstrong\u003eParameter\u003c\/strong\u003e\u003c\/th\u003e\n\u003cth\u003e\u003cstrong\u003eSpecification\u003c\/strong\u003e\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eModel\u003c\/td\u003e\n\u003ctd\u003eIS200TRLYH1BGE\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBrand\u003c\/td\u003e\n\u003ctd\u003eGE Fanuc\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOrigin\u003c\/td\u003e\n\u003ctd\u003eUSA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWeight\u003c\/td\u003e\n\u003ctd\u003e0.3 kg\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDimensions\u003c\/td\u003e\n\u003ctd\u003e3.5 x 13.0 x 13.5 cm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOperating Temp\u003c\/td\u003e\n\u003ctd\u003e0 to 60 deg C\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePower Consumption\u003c\/td\u003e\n\u003ctd\u003e10 W\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBoard Type\u003c\/td\u003e\n\u003ctd\u003eRelay Output Logic\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003ch3\u003eProfinet \/ EtherNet\/IP Deterministic Networks\u003c\/h3\u003e\n\u003cp\u003eThe IS200TRLYH1BGE functions as a high-density relay interface, managing the translation of low-voltage logic signals into high-current physical outputs. It utilizes backplane communication paths to receive commands from the Mark VI controller, ensuring deterministic execution of critical control functions. The board supports firmware flash compatibility to allow for updated control algorithms, and its layout is optimized for high-speed switching response times required in excitation and turbine control sequences. The module ensures consistent signal throughput by maintaining low-latency transitions across its on-board relay logic pathways.\u003c\/p\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cp\u003eQ: Is the IS200TRLYH1BGE designed for hot-swap operations in a live Mark VI rack?\u003c\/p\u003e\n\u003cp\u003eA: No, this board must not be installed or removed while the rack is powered. Doing so can cause damage to the backplane edge connectors and potential logic faults due to unexpected interruptions in the relay control bus.\u003c\/p\u003e\n\u003cp\u003eQ: How can relay wear be monitored on this board?\u003c\/p\u003e\n\u003cp\u003eA: Monitor the relay switching frequency and load current within the control software. Excessive high-current switching cycles may lead to contact degradation, which can be identified by inconsistent relay state transitions or audible chatter during operation.\u003c\/p\u003e\n\u003ch3\u003eField Installation Guidelines\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003ePower down the Mark VI I\/O rack and ensure all DC power inputs to the module are verified at 0 VDC.\u003c\/li\u003e\n\u003cli\u003eObserve standard anti-static procedures; use a grounded wrist strap when handling the IS200TRLYH1BGE to prevent damage to sensitive CMOS components.\u003c\/li\u003e\n\u003cli\u003eSlide the board into the designated rack slot, ensuring the backplane connector aligns correctly with the guide rails.\u003c\/li\u003e\n\u003cli\u003eSecure the board using the integrated front-panel fasteners to ensure a solid mechanical connection and proper chassis grounding.\u003c\/li\u003e\n\u003cli\u003eInspect the wiring to the terminal block to ensure no exposed conductor exists and that the terminal block is seated firmly on the board pins.\u003c\/li\u003e\n\u003c\/ol\u003e","brand":"GE FANUC","offers":[{"title":"Default Title","offer_id":52469254881592,"sku":"IS200TRLYH1BGE","price":220.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0893\/1616\/3896\/files\/IS200TRLYH1BGE.jpg?v=1780560038","url":"https:\/\/www.automodulexpert.com\/products\/is200trlyh1bge-ge-fanuc-circuit-board-new-original-stock","provider":"AutoModuleXpert Ltd.","version":"1.0","type":"link"}