{"product_id":"is200tturh1c-general-electric-termination-card-new-original-stock","title":"IS200TTURH1C General Electric Termination Card | New \u0026 Original Stock","description":"\u003cp\u003eThe \u003cstrong\u003eGeneral Electric IS200TTURH1C\u003c\/strong\u003e, also cataloged as the \u003cstrong\u003eIS200TTURH1C\u003c\/strong\u003e Termination Card, operates as a dedicated hardware component for field signal distribution and termination within Mark VI control system networks.\u003c\/p\u003e\n\u003ch3\u003eHardware Specifications\u003c\/h3\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003e\u003cstrong\u003eParameter\u003c\/strong\u003e\u003c\/th\u003e\n\u003cth\u003e\u003cstrong\u003eSpecification\u003c\/strong\u003e\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eModel\u003c\/td\u003e\n\u003ctd\u003eIS200TTURH1C\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBrand\u003c\/td\u003e\n\u003ctd\u003eGeneral Electric\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOrigin\u003c\/td\u003e\n\u003ctd\u003eUSA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWeight\u003c\/td\u003e\n\u003ctd\u003e0.3 kg\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDimensions\u003c\/td\u003e\n\u003ctd\u003e3.5 x 13.0 x 13.5 cm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOperating Temp\u003c\/td\u003e\n\u003ctd\u003e0 to 60 deg C\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePower Consumption\u003c\/td\u003e\n\u003ctd\u003e5 W\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eApplication\u003c\/td\u003e\n\u003ctd\u003eField Signal Interface\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003ch3\u003eProfinet \/ EtherNet\/IP Deterministic Networks\u003c\/h3\u003e\n\u003cp\u003eThe IS200TTURH1C serves as the physical interface layer, managing the transition between field-side wiring and the internal control system bus. It provides I\/O density scaling by consolidating incoming field signals into organized terminal blocks, ensuring that each loop is properly routed to the corresponding I\/O processor. The board architecture is optimized for high-density signal throughput, maintaining signal integrity and deterministic connectivity across the control platform. Firmware compatibility allows for seamless integration with existing Mark VI rack modules.\u003c\/p\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cp\u003eQ: Can the IS200TTURH1C be hot-swapped during active system operation?\u003c\/p\u003e\n\u003cp\u003eA: No, this termination card is a passive physical component that must not be disconnected while the system is energized. Isolating the terminal block requires the associated I\/O rack power to be disabled to prevent signal corruption or equipment damage.\u003c\/p\u003e\n\u003cp\u003eQ: How is the shield drain wire managed on this terminal card?\u003c\/p\u003e\n\u003cp\u003eA: Shield drain wires should be terminated at the designated chassis ground bar located on the card assembly. Ensure that shields are not daisy-chained to signal common terminals to avoid ground loops.\u003c\/p\u003e\n\u003ch3\u003eField Installation Guidelines\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003ePower down the corresponding I\/O rack and verify the absence of voltage before commencing installation.\u003c\/li\u003e\n\u003cli\u003eEnsure the mounting surface is clean and free of conductive debris. Secure the IS200TTURH1C to the cabinet panel using the provided hardware to maintain electrical continuity with the chassis ground.\u003c\/li\u003e\n\u003cli\u003eTerminate field wiring in accordance with the project loop diagrams, ensuring proper wire gauge and stripping lengths are maintained to prevent shorting between adjacent terminals.\u003c\/li\u003e\n\u003cli\u003eVerify all terminal connections are torqued to specifications. Avoid excessive mechanical stress on the board-to-cable connectors when plugging in the ribbon or I\/O cable harnesses.\u003c\/li\u003e\n\u003cli\u003ePerform a point-to-point continuity check from the field device to the termination card before signaling the control processor, ensuring all paths are isolated and properly routed.\u003c\/li\u003e\n\u003c\/ol\u003e","brand":"GE FANUC","offers":[{"title":"Default Title","offer_id":52468557218104,"sku":"IS200TTURH1C","price":220.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0893\/1616\/3896\/files\/IS200TTURH1C.jpg?v=1780560041","url":"https:\/\/www.automodulexpert.com\/products\/is200tturh1c-general-electric-termination-card-new-original-stock","provider":"AutoModuleXpert Ltd.","version":"1.0","type":"link"}