{"product_id":"is2020rkpsg2a-general-electric-power-supply-new-original-stock","title":"IS2020RKPSG2A General Electric Power Supply | New \u0026 Original Stock","description":"\u003cp\u003eThe \u003cstrong\u003eGeneral Electric IS2020RKPSG2A\u003c\/strong\u003e, also cataloged as the \u003cstrong\u003eIS2020RKPSG2A\u003c\/strong\u003e Power Supply, operates as a dedicated hardware component for VME backplane voltage regulation and power distribution within Mark VI control system platforms.\u003c\/p\u003e\n\u003ch3\u003eHardware Specifications\u003c\/h3\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003e\u003cstrong\u003eParameter\u003c\/strong\u003e\u003c\/th\u003e\n\u003cth\u003e\u003cstrong\u003eSpecification\u003c\/strong\u003e\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eModel\u003c\/td\u003e\n\u003ctd\u003eIS2020RKPSG2A\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBrand\u003c\/td\u003e\n\u003ctd\u003eGeneral Electric\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOrigin\u003c\/td\u003e\n\u003ctd\u003eUSA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWeight\u003c\/td\u003e\n\u003ctd\u003e1.85 kg\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDimensions\u003c\/td\u003e\n\u003ctd\u003e25.0 cm x 15.5 cm x 12.0 cm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOperating Temp\u003c\/td\u003e\n\u003ctd\u003e0 to 60 deg C\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePower Consumption\u003c\/td\u003e\n\u003ctd\u003eInput: 125 VDC or 120\/240 VAC nominal\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOutput Voltage\u003c\/td\u003e\n\u003ctd\u003e+5 VDC, +12 VDC, -12 VDC (VME standard)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003ch3\u003eBackplane Bus Communication Velocity\u003c\/h3\u003e\n\u003cp\u003eThe IS2020RKPSG2A is engineered to provide stable, low-noise DC output to the VME backplane bus. The power distribution architecture is designed to support the specific backplane bus communication velocity required by high-speed processor modules within the Mark VI rack. Stable voltage rails are required to ensure that the timing margins for data transmission across the VME bus remain within specified tolerances, preventing communication jitter or bit errors caused by power ripple or sagging during transient load events.\u003c\/p\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cp\u003eQ: Is this power supply capable of being operated in a redundant configuration?\u003c\/p\u003e\n\u003cp\u003eA: Yes, the system architecture supports dual-redundant power supplies. Load sharing is managed automatically by the internal circuitry, allowing one module to provide full system power should the other experience a fault.\u003c\/p\u003e\n\u003cp\u003eQ: What are the indicators for a module fault?\u003c\/p\u003e\n\u003cp\u003eA: The front panel status LEDs provide immediate feedback. A \"Supply OK\" indicator signifies that the internal output rails are within their nominal operating ranges. If the internal logic detects an over-voltage or under-voltage condition on any output rail, the fault LED will illuminate and the status signal will be sent to the controller.\u003c\/p\u003e\n\u003ch3\u003eField Installation Guidelines\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eVerify that the input power source matches the rating label on the module before connection to avoid catastrophic internal failure.\u003c\/li\u003e\n\u003cli\u003eEnsure the power supply is fully inserted into the designated VME slot; the backplane connectors must be aligned to prevent pin damage during insertion.\u003c\/li\u003e\n\u003cli\u003eTighten the top and bottom captive screws to ensure the module chassis maintains a solid electrical bond with the rack frame for electromagnetic shielding.\u003c\/li\u003e\n\u003cli\u003eMeasure the output voltages at the backplane test points after installation to confirm proper regulation before installing any I\/O packs or controller modules in the rack.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"GE FANUC","offers":[{"title":"Default Title","offer_id":52487741276472,"sku":"IS2020RKPSG2A","price":220.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0893\/1616\/3896\/files\/IS2020RKPSG2A2.jpg?v=1781078007","url":"https:\/\/www.automodulexpert.com\/products\/is2020rkpsg2a-general-electric-power-supply-new-original-stock","provider":"AutoModuleXpert Ltd.","version":"1.0","type":"link"}