{"product_id":"is215vcmih2b-ge-vme-communication-interface-card-datasheet","title":"IS215VCMIH2B GE VME Communication Interface Card | Datasheet","description":"\u003cp\u003eThe \u003cstrong\u003eGE IS215VCMIH2B\u003c\/strong\u003e, also cataloged as the \u003cstrong\u003eIS215VCMI\u003c\/strong\u003e Communication Interface Card, operates as a dedicated hardware component for high-speed data exchange and system-level communication within Mark VIe control platforms.\u003c\/p\u003e\n\u003ch3\u003eHardware Specifications\u003c\/h3\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003e\u003cstrong\u003eParameter\u003c\/strong\u003e\u003c\/th\u003e\n\u003cth\u003e\u003cstrong\u003eSpecification\u003c\/strong\u003e\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eModel\u003c\/td\u003e\n\u003ctd\u003eIS215VCMIH2B\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBrand\u003c\/td\u003e\n\u003ctd\u003eGE\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOrigin\u003c\/td\u003e\n\u003ctd\u003eUSA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWeight\u003c\/td\u003e\n\u003ctd\u003e 0.45 kg\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDimensions\u003c\/td\u003e\n\u003ctd\u003eStandard VME board form factor\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOperating Temp\u003c\/td\u003e\n\u003ctd\u003e-30 deg C to +65 deg C\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePower Consumption\u003c\/td\u003e\n\u003ctd\u003eVME bus load dependent\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eInterface Type\u003c\/td\u003e\n\u003ctd\u003eVME Bus communication\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003ch3\u003ePLC\/DCS Firmware and Backplane Integration\u003c\/h3\u003e\n\u003cp\u003eThe \u003cstrong\u003eIS215VCMIH2B\u003c\/strong\u003e serves as the primary VME interface utilized to execute deterministic data transfer across Mark VIe system platforms. The board supports high-speed backplane bus communication velocity, enabling the synchronization of control loop data with central processors. Firmware flash compatibility is strictly managed via the I\/O rack backplane, ensuring that the module correctly registers with the controller during the boot sequence. The integration allows for robust I\/O density scaling, as the VCMI handles the translation of internal bus signals to external communication protocols, maintaining data consistency without adding latency.\u003c\/p\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cp\u003eQ: Can the IS215VCMIH2B be replaced while the VME rack is powered?\u003c\/p\u003e\n\u003cp\u003eA: Hot-swapping is not permitted for this communication interface. The VME rack power must be de-energized to prevent electrical arcing at the backplane pins and to avoid corruption of the communication state during board removal.\u003c\/p\u003e\n\u003cp\u003eQ: How is the firmware version verified on this board?\u003c\/p\u003e\n\u003cp\u003eA: The firmware revision is identified through the host controller's configuration software (ToolboxST) once the board is seated and the rack is energized, which performs a hardware ID and firmware checksum validation.\u003c\/p\u003e\n\u003ch3\u003eField Installation Guidelines\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003eEnsure the Mark VIe cabinet is de-energized before handling the PCB to prevent electrostatic discharge damage.\u003c\/li\u003e\n\u003cli\u003eAlign the board with the VME backplane card guides; ensure the module is fully inserted until the connector pins are seated.\u003c\/li\u003e\n\u003cli\u003eSecure the front panel handle locks to ensure the board is grounded to the cabinet chassis.\u003c\/li\u003e\n\u003cli\u003eVerify that all communication cabling is properly shielded and grounded at the signal entry point to minimize electromagnetic interference.\u003c\/li\u003e\n\u003cli\u003eInspect the backplane connector for any signs of oxidation or bent pins prior to installation.\u003c\/li\u003e\n\u003cli\u003eOnce installed, confirm the module status indicator LED is in the active, steady-state mode as specified in the control system diagnostic logs.\u003c\/li\u003e\n\u003c\/ol\u003e","brand":"GE FANUC","offers":[{"title":"Default Title","offer_id":52479410700600,"sku":"IS215VCMIH2B","price":220.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0893\/1616\/3896\/files\/IS215VCMIH2B_1d0fb722-5b1e-497b-9d05-56c88dd146fd.jpg?v=1780905032","url":"https:\/\/www.automodulexpert.com\/products\/is215vcmih2b-ge-vme-communication-interface-card-datasheet","provider":"AutoModuleXpert Ltd.","version":"1.0","type":"link"}