{"product_id":"is220ydoas1a-ge-discrete-output-pack-new-original-stock","title":"IS220YDOAS1A GE Discrete Output Pack | New \u0026 Original Stock","description":"\u003cp\u003eConfigured for high-speed switching of discrete field devices in Mark VIe control system platforms, the \u003cstrong\u003eGE IS220YDOAS1A\u003c\/strong\u003e (\u003cstrong\u003eIS220YDOAS1\u003c\/strong\u003e I\/O Pack) provides direct physical execution of relay or transistorized output commands. This module interfaces between the controller and field-side actuators to provide discrete state control across the system network.\u003c\/p\u003e\n\u003ch3\u003eHardware Specifications\u003c\/h3\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003e\u003cstrong\u003eParameter\u003c\/strong\u003e\u003c\/th\u003e\n\u003cth\u003e\u003cstrong\u003eSpecification\u003c\/strong\u003e\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eModel\u003c\/td\u003e\n\u003ctd\u003eIS220YDOAS1A\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBrand\u003c\/td\u003e\n\u003ctd\u003eGE\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOrigin\u003c\/td\u003e\n\u003ctd\u003eUSA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWeight\u003c\/td\u003e\n\u003ctd\u003e0.6 KG\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDimensions\u003c\/td\u003e\n\u003ctd\u003e28 cm x 11.5 cm x 4.5 cm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOperating Temp\u003c\/td\u003e\n\u003ctd\u003e-30 deg C to +65 deg C\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePower Consumption\u003c\/td\u003e\n\u003ctd\u003e24 VDC (Backplane powered)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eI\/O Type\u003c\/td\u003e\n\u003ctd\u003eDiscrete Output\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003ch3\u003eProfinet \/ EtherNet\/IP Deterministic Networks\u003c\/h3\u003e\n\u003cp\u003eThe IS220YDOAS1A operates within the Mark VIe I\/O pack architecture, facilitating deterministic command execution via the internal backplane bus. Communication velocity is maintained through high-speed scan cycles, ensuring that output commands from the processor are reflected at the field terminals with minimal latency. Users must ensure that firmware revisions on the I\/O pack are aligned with the controller configuration to maintain network synchronization and prevent potential state-mismatch errors during high-frequency switching operations.\u003c\/p\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cp\u003eQ: Does this module support internal loop monitoring for the output channels?\u003c\/p\u003e\n\u003cp\u003eA: Yes, the I\/O pack provides feedback monitoring to verify the state of the output circuit. If a discrepancy between the commanded state and the load current is detected, the module generates a diagnostic alarm for the host controller.\u003c\/p\u003e\n\u003cp\u003eQ: Can the output modules be configured for redundant output operation?\u003c\/p\u003e\n\u003cp\u003eA: In a Triple Modular Redundant (TMR) setup, these modules work in conjunction with the terminal board to provide redundant state control. Ensure the I\/O pack hardware and the control software are correctly mapped for the redundant mode to avoid signal voting conflicts.\u003c\/p\u003e\n\u003ch3\u003eField Installation Guidelines\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eIsolate all output power circuits and remove system control power before attempting to seat the module in the chassis.\u003c\/li\u003e\n\u003cli\u003eInspect the backplane slot for pin alignment; gently slide the module until the locking tabs secure it against the rack.\u003c\/li\u003e\n\u003cli\u003eConfirm that the terminal board wiring matches the discrete output voltage requirements (typically 24 VDC) to prevent damage to the output drivers.\u003c\/li\u003e\n\u003cli\u003eEnsure all field cables connected to the terminal interface are properly shielded to prevent noise-induced false states on the discrete output lines.\u003c\/li\u003e\n\u003cli\u003eVerify the module status via the diagnostic LEDs; a steady green status indicates successful communication with the controller, while red indicators signal an internal fault or loss of communication.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"GE FANUC","offers":[{"title":"Default Title","offer_id":52479437734200,"sku":"IS220YDOAS1A","price":220.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0893\/1616\/3896\/files\/IS220YDOAS1A.jpg?v=1780905031","url":"https:\/\/www.automodulexpert.com\/products\/is220ydoas1a-ge-discrete-output-pack-new-original-stock","provider":"AutoModuleXpert Ltd.","version":"1.0","type":"link"}