{"product_id":"motion-controller-module-ge-ic694dsm314","title":"Motion Controller Module GE IC694DSM314","description":"\u003cp\u003eThe \u003cstrong\u003eGE IC694DSM314\u003c\/strong\u003e, also cataloged as the \u003cstrong\u003eIC694DSM314\u003c\/strong\u003e Motion Controller Module, operates as a dedicated hardware component for 1-2 axis digital servo and 1-4 axis analog servo control within PLC and machine control platforms.\u003c\/p\u003e\n\u003ch3\u003eHardware Specifications\u003c\/h3\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003eParameter\u003c\/th\u003e\n\u003cth\u003eSpecification\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eModel\u003c\/td\u003e\n\u003ctd\u003eIC694DSM314\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBrand\u003c\/td\u003e\n\u003ctd\u003eGE\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOrigin\u003c\/td\u003e\n\u003ctd\u003eUSA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWeight\u003c\/td\u003e\n\u003ctd\u003e0.3kg\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDimensions\u003c\/td\u003e\n\u003ctd\u003eStandard PACSystems RX3i module form factor\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOperating Temp\u003c\/td\u003e\n\u003ctd\u003eNot specified\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePower Consumption\u003c\/td\u003e\n\u003ctd\u003eNot specified\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eServo Support\u003c\/td\u003e\n\u003ctd\u003e1-2 Axis Digital \/ 1-4 Axis Analog\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003ch3\u003eProfinet \/ EtherNet\/IP Deterministic Networks\u003c\/h3\u003e\n\u003cp\u003eThe \u003cstrong\u003eGE IC694DSM314\u003c\/strong\u003e integrates into the PACSystems RX3i control architecture to execute deterministic motion profiles. The module supports high-speed backplane bus communication velocity, allowing for precise synchronization between the PLC processor and remote servo drives. Firmware flash compatibility is governed by the host controller revision; the module requires specific firmware versions to support the command execution for 1-2 axis digital or 1-4 axis analog servo configurations. Signal integrity during axis motion is maintained through high-density shielding of the interface connectors, preventing electromagnetic interference from degrading the low-voltage control signals transmitted to the servo drive network.\u003c\/p\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cp\u003eQ: Is this module hot-swappable while the PACSystems rack is powered? A: No. The IC694DSM314 must be removed only after the rack power has been de-energized to prevent short-circuiting the backplane pins and to ensure the servo drive network remains in a safe, inhibited state.\u003c\/p\u003e\n\u003cp\u003eQ: How does the module handle axis configuration? A: Axis configuration is performed via the programming environment software, which defines the motion parameters, feedback scaling, and control loop gain values stored in the module's internal memory during initialization.\u003c\/p\u003e\n\u003ch3\u003eField Installation Guidelines\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eMounting\u003c\/strong\u003e: Seat the module firmly into the RX3i baseplate. Engage the locking levers to ensure solid electrical contact with the backplane communication bus.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eShielding\u003c\/strong\u003e: Use double-shielded twisted-pair cabling for all analog servo signals to mitigate noise coupling from adjacent power lines. Ground the cable shields at the module's designated terminal ground point.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWiring Separation\u003c\/strong\u003e: Route high-voltage power cables at least 150 mm away from the motion controller signal cabling to eliminate inductive noise.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCalibration\u003c\/strong\u003e: After installation, perform a software-guided axis homing procedure to calibrate the digital or analog feedback offsets before initiating automated machine cycles.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"GE FANUC","offers":[{"title":"Default Title","offer_id":52596582056248,"sku":"IC694DSM314","price":220.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0893\/1616\/3896\/files\/IC694DSM314.jpg?v=1782980881","url":"https:\/\/www.automodulexpert.com\/products\/motion-controller-module-ge-ic694dsm314","provider":"AutoModuleXpert Ltd.","version":"1.0","type":"link"}