{"product_id":"relay-output-board-ge-ds200tcrag1a","title":"Relay Output Board GE DS200TCRAG1A","description":"\u003cp\u003eConfigured for discrete signal execution in Mark V LM control system platforms, the \u003cstrong\u003eGE DS200TCRAG1A\u003c\/strong\u003e (\u003cstrong\u003eDS200TCRAG1A\u003c\/strong\u003e Relay Output Board) provides direct physical\/electrical execution. This hardware component serves as a primary switching interface, utilized to execute logic-driven commands across turbine and power generation control networks. The board translates low-voltage control signals into higher-capacity relay contact states to drive field-side auxiliary equipment, ensuring deterministic state changes for critical operational processes.\u003c\/p\u003e\n\u003ch3\u003eHardware Specifications\u003c\/h3\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003e\u003cstrong\u003eParameter\u003c\/strong\u003e\u003c\/th\u003e\n\u003cth\u003e\u003cstrong\u003eSpecification\u003c\/strong\u003e\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eModel\u003c\/td\u003e\n\u003ctd\u003eDS200TCRAG1A\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBrand\u003c\/td\u003e\n\u003ctd\u003eGE\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOrigin\u003c\/td\u003e\n\u003ctd\u003eUSA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWeight\u003c\/td\u003e\n\u003ctd\u003e0.15 kg\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDimensions\u003c\/td\u003e\n\u003ctd\u003e55 mm x 65 mm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOperating Temp\u003c\/td\u003e\n\u003ctd\u003e0 to 50 deg C\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePower Consumption\u003c\/td\u003e\n\u003ctd\u003eDependent on relay coil activation states\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eProduct Type\u003c\/td\u003e\n\u003ctd\u003eRelay Output Board\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003ch3\u003eIndustrial Control and I\/O Density Scaling\u003c\/h3\u003e\n\u003cp\u003eThe DS200TCRAG1A facilitates precise I\/O density scaling within the Mark V LM cabinet architecture. By optimizing backplane bus communication velocity, the board ensures that relay switching commands are executed with minimal latency. Firmware flash compatibility is aligned with standard Mark V LM series control requirements, ensuring that the relay states are synchronized with the central processor logic without causing bus contention or signal timing errors.\u003c\/p\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cp\u003eQ: Are the relay outputs on the DS200TCRAG1A capable of hot-swapping during turbine operation?\u003c\/p\u003e\n\u003cp\u003eA: No. Relay boards must be replaced with the control power removed and the field-side devices safely isolated to prevent unintended activation of auxiliary equipment during the replacement procedure.\u003c\/p\u003e\n\u003cp\u003eQ: How should the inductive load be handled when connected to these relay outputs?\u003c\/p\u003e\n\u003cp\u003eA: External suppression diodes or RC snubbers should be utilized for all inductive loads to prevent contact pitting and excessive arcing during relay opening\/closing cycles.\u003c\/p\u003e\n\u003ch3\u003eField Installation Guidelines\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003eVerify that all control power and field-side excitation sources are locked out in accordance with standard site safety procedures.\u003c\/li\u003e\n\u003cli\u003eInspect the PCB edge connectors for any oxidation or debris; use a non-residue electronic cleaner if necessary.\u003c\/li\u003e\n\u003cli\u003eSlide the module into the designated Mark V LM chassis slot. Apply firm pressure to ensure the pins seat fully into the backplane connector.\u003c\/li\u003e\n\u003cli\u003eSecure the board using the provided mounting hardware to ensure stability against cabinet vibrations.\u003c\/li\u003e\n\u003cli\u003eTerminate field wiring to the corresponding terminal blocks, ensuring that all wires are strain-relieved to prevent tension on the board-to-chassis connection.\u003c\/li\u003e\n\u003cli\u003eConfirm that the relay contact ratings are not exceeded by the field device current draw to ensure long-term hardware reliability.\u003c\/li\u003e\n\u003c\/ol\u003e","brand":"GE FANUC","offers":[{"title":"Default Title","offer_id":52613978620216,"sku":"DS200TCRAG1A","price":220.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0893\/1616\/3896\/files\/DS200TCRAG1A.jpg?v=1783412336","url":"https:\/\/www.automodulexpert.com\/products\/relay-output-board-ge-ds200tcrag1a","provider":"AutoModuleXpert Ltd.","version":"1.0","type":"link"}